Hi Erich I put my /etc/modprobe.conf (from the standalone install) into the image and set up networking to UYOK. It installed and rebooted the nodes fine.
However, ssh across the cluster does not work and thus the 'Complete Cluster Setup' and 'Test Cluster Setup' parts are failing. I think I know why it is happenning, but it probably should be a new thread if I can't resolve it. I will have another go on Monday. Thanks Pen On Thu, Nov 23, 2006 at 06:22:23PM +0100, Erich Focht wrote: > Hello Pen, > > how did your hardware.lst file look like? > > Did you try booting one of the client nodes into a rescue system (from the > RHEL4 CD)? If you do that, please have a look at the /etc/modprobe.conf file > which was generated by systemconfigurator. Does it contain the mptsas module? > > You could also simply copy the /etc/modprobe.conf which you attached to your > email into the image. systemconfigurator is just editing that file based on > the hardware it detects. > > Regards, > Erich > > > On Thursday 23 November 2006 16:41, Pen Richardson wrote: > > Hi > > > > I have been encountering a problem that resembles a thread on the mailing > > list - 'SATA/SAS installation issue'. The cluster I am building > > consists of a 14 of Dell Poweredge 1950 Servers. The master node having two > > 300GB SAS disks and the compute nodes a single 32GB SAS disk each. > > > > At first when trying to image the clients I was getting this error: > > > > NO DISK DEVICE FILES WERE FOUND. THIS USUALLY MEANS THE KERNEL DID NOT > > RECOGNIZE ANY OF THE ATTACHED DISKS. > > > > So I tried putting a hardware.lst file in the specified place in my image. > > Still the same error. After that I tried the UYOK option with hardware.lst > > still in place. The clients appeared to image ok but when I rebooted them I > > got a kernel panic like that in the thread mentioned above. > > > > The info below was gathered from a standalone install of redhat on one of > > the clients. I used this info to try and set up the hardware.lst > > > > Has anyone had success with similar kit or got any suggestions of what to > > try next? > > > > Many Thanks > > Pen > > > > lspci > > ----- > > > > 00:00.0 Host bridge: Intel Corporation 5000X Chipset Memory Controller Hub > > (rev 12) > > 00:02.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 > > Port 2 (rev 12) > > 00:03.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 > > Port 3 (rev 12) > > 00:04.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 > > Port 4-5 (rev 12) > > 00:05.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 > > Port 5 (rev 12) > > 00:06.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 > > Port 6-7 (rev 12) > > 00:07.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 > > Port 7 (rev 12) > > 00:10.0 Host bridge: Intel Corporation 5000 Series Chipset Error Reporting > > Registers (rev 12) > > 00:10.1 Host bridge: Intel Corporation 5000 Series Chipset Error Reporting > > Registers (rev 12) > > 00:10.2 Host bridge: Intel Corporation 5000 Series Chipset Error Reporting > > Registers (rev 12) > > 00:11.0 Host bridge: Intel Corporation 5000 Series Chipset Reserved > > Registers (rev 12) > > 00:13.0 Host bridge: Intel Corporation 5000 Series Chipset Reserved > > Registers (rev 12) > > 00:15.0 Host bridge: Intel Corporation 5000 Series Chipset FBD Registers > > (rev 12) > > 00:16.0 Host bridge: Intel Corporation 5000 Series Chipset FBD Registers > > (rev 12) > > 00:1c.0 PCI bridge: Intel Corporation 631xESB/632xESB/3100 Chipset PCI > > Express Root Port 1 (rev 09) > > 00:1d.0 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI > > USB Controller #1 (rev 09) > > 00:1d.1 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI > > USB Controller #2 (rev 09) > > 00:1d.2 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI > > USB Controller #3 (rev 09) > > 00:1d.7 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset EHCI > > USB2 Controller (rev 09) > > 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d9) > > 00:1f.0 ISA bridge: Intel Corporation 631xESB/632xESB/3100 Chipset LPC > > Interface Controller (rev 09) > > 00:1f.1 IDE interface: Intel Corporation 631xESB/632xESB IDE Controller (rev > > 09) > > 01:00.0 PCI bridge: Intel Corporation 6702PXH PCI Express-to-PCI Bridge A > > (rev 09) > > 02:08.0 SCSI storage controller: LSI Logic / Symbios Logic SAS1068 PCI-X > > Fusion-MPT SAS (rev 01) > > 03:00.0 PCI bridge: Broadcom: Unknown device 0103 (rev c2) > > 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 > > Gigabit Ethernet (rev 11) > > 05:00.0 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express Upstream > > Port (rev 01) > > 05:00.3 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express to PCI-X > > Bridge (rev 01) > > 06:00.0 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express Downstream > > Port E1 (rev 01) > > 06:01.0 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express Downstream > > Port E2 (rev 01) > > 07:00.0 PCI bridge: Broadcom: Unknown device 0103 (rev c2) > > 08:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 > > Gigabit Ethernet (rev 11) > > 0f:0d.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02) > > > > lspci -n > > -------- > > 00:00.0 Class 0600: 8086:25c0 (rev 12) > > 00:02.0 Class 0604: 8086:25e2 (rev 12) > > 00:03.0 Class 0604: 8086:25e3 (rev 12) > > 00:04.0 Class 0604: 8086:25f8 (rev 12) > > 00:05.0 Class 0604: 8086:25e5 (rev 12) > > 00:06.0 Class 0604: 8086:25f9 (rev 12) > > 00:07.0 Class 0604: 8086:25e7 (rev 12) > > 00:10.0 Class 0600: 8086:25f0 (rev 12) > > 00:10.1 Class 0600: 8086:25f0 (rev 12) > > 00:10.2 Class 0600: 8086:25f0 (rev 12) > > 00:11.0 Class 0600: 8086:25f1 (rev 12) > > 00:13.0 Class 0600: 8086:25f3 (rev 12) > > 00:15.0 Class 0600: 8086:25f5 (rev 12) > > 00:16.0 Class 0600: 8086:25f6 (rev 12) > > 00:1c.0 Class 0604: 8086:2690 (rev 09) > > 00:1d.0 Class 0c03: 8086:2688 (rev 09) > > 00:1d.1 Class 0c03: 8086:2689 (rev 09) > > 00:1d.2 Class 0c03: 8086:268a (rev 09) > > 00:1d.7 Class 0c03: 8086:268c (rev 09) > > 00:1e.0 Class 0604: 8086:244e (rev d9) > > 00:1f.0 Class 0601: 8086:2670 (rev 09) > > 00:1f.1 Class 0101: 8086:269e (rev 09) > > 01:00.0 Class 0604: 8086:032c (rev 09) > > 02:08.0 Class 0100: 1000:0054 (rev 01) > > 03:00.0 Class 0604: 1166:0103 (rev c2) > > 04:00.0 Class 0200: 14e4:164c (rev 11) > > 05:00.0 Class 0604: 8086:3500 (rev 01) > > 05:00.3 Class 0604: 8086:350c (rev 01) > > 06:00.0 Class 0604: 8086:3510 (rev 01) > > 06:01.0 Class 0604: 8086:3514 (rev 01) > > 07:00.0 Class 0604: 1166:0103 (rev c2) > > 08:00.0 Class 0200: 14e4:164c (rev 11) > > 0f:0d.0 Class 0300: 1002:515e (rev 02) > > > > modprobe.conf > > ------------- > > > > alias eth0 bnx2 > > alias eth1 bnx2 > > alias scsi_hostadapter mptbase > > alias scsi_hostadapter1 mptscsi > > alias scsi_hostadapter2 mptfc > > alias scsi_hostadapter3 mptspi > > alias scsi_hostadapter4 mptsas > > alias scsi_hostadapter5 mptscsih > > alias usb-controller ehci-hcd > > alias usb-controller1 uhci-hcd > -- Penny Richardson Manchester Computing University of Manchester Tel: 0161 275 6408 Email: [EMAIL PROTECTED] ------------------------------------------------------------------------- Take Surveys. Earn Cash. Influence the Future of IT Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys - and earn cash http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV _______________________________________________ Oscar-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/oscar-users
