I've attached the relevant parts of the dmesg output for both a failed load
and a successful load. I've attached the full output of both boot logs as
attachments also.
- David
Failed Boot:
Freeing init memory: 1376K
mmc0: new SD card at address e624
mmcblk0: mmc0:e624 SU02G 1.84 GiB
mmcblk0: p1
mount: mounting /dev/mmcblk0p1 on /r failed: No such device or address
1Wire touchscreen OK
/init: line 103: can't open /r/dev/console: no such file
Kernel panic - not syncing: Attempted to kill init!
[<c016fde8>] (unwind_backtrace+0x0/0xe4) from [<c033e200>]
(panic+0x68/0x184)
[<c033e200>] (panic+0x68/0x184) from [<c0180aac>] (do_exit+0x68/0x668)
[<c0180aac>] (do_exit+0x68/0x668) from [<c01813d8>]
(do_group_exit+0xb0/0xe4)
[<c01813d8>] (do_group_exit+0xb0/0xe4) from [<c018141c>]
(sys_exit_group+0x10/0x18)
[<c018141c>] (sys_exit_group+0x10/0x18) from [<c016a640>]
(ret_fast_syscall+0x0/0x30)
one_wire_status: 2
Successful Boot:
Freeing init memory: 1376K
mmc0: new SD card at address e624
mmcblk0: mmc0:e624 SU02G 1.84 GiB
mmcblk0: p1
EXT2-fs (mmcblk0p1): warning: mounting unchecked fs, running e2fsck is
recommended
1Wire touchscreen OK
init started: BusyBox v1.20.2 (2013-03-07 01:03:05 EST)
starting pid 382, tty '/dev/console': '/etc/init.d/rcS'
mounting filesystems...done.
running rc.d services...
U-Boot 1.1.6-ptx-2011.11.0 (Mar 6 2013 - 23:23:16) for FriendlyARM MINI6410
CPU: S3C6410@532MHz
Fclk = 532MHz, Hclk = 133MHz, Pclk = 66MHz, Serial = CLKUART (SYNC
Mode)
Board: MINI6410
DRAM: 256 MB
Flash: 0 kB
NAND: 1024 MB
MMC:
Setting up an SD card with 3862528 sectors:
Useable area ends with sector 3862526.
BL1 area starts in sector 3862510.
Environment area starts in sector 3862254.
BL2 area starts in sector 3861742.
Kernel area starts in sector 3850222.
1887 MB
In: serial
Out: serial
Err: serial
MAC: 08:90:90:90:90:90
Hit any key to stop autoboot: 0
Reading zImage from block 3850222.. Completed!
Boot with zImage
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Initializing cgroup subsys cpu
Linux version 2.6.38 (david@devbox) (gcc version 4.5.1 (ctng-1.8.1-FA) ) #1
PREEMPT Thu Mar 7 01:38:42 EST 2013
CPU: ARMv6-compT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: MINI6410
Memory policy: ECC disabled, Data cache writeback
CPU S3C6410 (id 0x36410101)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
camera: no parent clock specified
S3C64XX: PLL settings, A=532000000, M=532000000, E=24000000
S3C64XX: HCLK2=266000000, HCLK=133000000, PCLK=66500000
mout_apll: source is fout_apll (1), rate is 532000000
mout_epll: source is epll (1), rate is 24000000
mout_mpll: source is mpll (1), rate is 532000000
mmc_bus: source is mout_epll (0), rate is 24000000
mmc_bus: source is mout_epll (0), rate is 24000000
mmc_bus: source is mout_epll (0), rate is 24000000
usb-bus-host: source is clk_48m (0), rate is 48000000
uclk1: source is dout_mpll (1), rate is 66500000
spi-bus: source is mout_epll (0), rate is 24000000
spi-bus: source is mout_epll (0), rate is 24000000
audio-bus: source is mout_epll (0), rate is 24000000
audio-bus: source is mout_epll (0), rate is 24000000
audio-bus: source is mout_epll (0), rate is 24000000
irda-bus: source is mout_epll (0), rate is 24000000
camera: no parent clock specified
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: root=/dev/mmcblk0p1 rootwait console=ttySAC0,115200
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 255416k/255416k available, 6728k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xff000000 - 0xffe00000 ( 14 MB)
vmalloc : 0xd0800000 - 0xf6000000 ( 600 MB)
lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc0160000 (1376 kB)
.text : 0xc0160000 - 0xc04005c0 (2690 kB)
.data : 0xc0402000 - 0xc0421fa0 ( 128 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Preemptable hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:246
VIC @f6000000: id 0x00041192, vendor 0x41
VIC @f6010000: id 0x00041192, vendor 0x41
Console: colour dummy device 80x30
console [ttySAC0] enabled
Calibrating delay loop... 530.84 BogoMIPS (lpj=2654208)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registers3c64xx_dma_init: Registering DMA channels
PL080: IRQ 73, at d0808000, channels 0..8
PL080: IRQ 74, at d080c000, channels 8..16
S3C6410: Initialising architecture
bio: create slab <bio-0> at 0
s3c-i2c s3c2440-i2c: slave address 0x10
s3c-i2c s3c2440-i2c: bus frequency set to 64 KHz
s3c-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
NetWinder Floating Point Emulator V0.97 (double precision)
msgmni has been set to 498
io scheduler noop registered (default)
io scheduler cfq registered
S3C_LCD clock got enabled :: 133.000 Mhz
LCD TYPE :: A70 will be initialized
Window[0] - FB1: map_video_memory: clear ff000000:00177000
FB1: map_video_memory: dma=5f000000 cpu=ff000000 size=00177000
Window[0] - FB2: map_video_memory: clear ff0bb800:000bb800
FB2: map_video_memory: dma=5f0bb800 cpu=ff0bb800 size=000bb800
Console: switching to colour frame buffer device 100x30
fb0: s3cfb frame buffer device
backlight initialized
s3c6400-uart.0: ttySAC0 at MMIO 0x7f005000 (irq = 16) is a S3C6400/10
s3c6400-uart.1: ttySAC1 at MMIO 0x7f005400 (irq = 20) is a S3C6400/10
s3c6400-uart.2: ttySAC2 at MMIO 0x7f005800 (irq = 24) is a S3C6400/10
s3c6400-uart.3: ttySAC3 at MMIO 0x7f005c00 (irq = 28) is a S3C6400/10
adc initialized
loop: module loaded
S3C NAND Driver, (c) 2008 Samsung Electronics
S3C NAND Driver is using hardware ECC.
NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit)
Creating 3 MTD partitions on "NAND 1GiB 3,3V 8-bit":
0x000000000000-0x000000080000 : "Bootloader"
0x000000080000-0x000000580000 : "Kernel"
0x000000580000-0x000040000000 : "File System"
dm9000 Ethernet Driver, V1.31
eth0: dm9000a at d081e000,d0c00004 IRQ 108 MAC: 08:90:90:90:90:90 (chip)
mousedev: PS/2 mouse device common for all mice
touchscreen-1wire initialized
backlie as /devices/virtual/input/input0
ts-if initialized
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
one_wire_status: 4
s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133000000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133000000 Hz)
one_wire_status: 4
s3c-sdhci s3c-sdhci.0: clock source 2: mmc_bus (24000000 Hz)
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133000000 Hz)
one_wire_status: 4
s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133000000 Hz)
s3c-sdhci s3c-sdhci.1: clock source 2: mmc_bus (24000000 Hz)
mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
TCP cubic registered
NET: Registered protocol family 17
VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
s3c-rtc s3c64xx-rtc: setting system clock to 2013-03-07 17:11:46 UTC
(1362676306)
Freeing init memory: 1376K
mmc0: new SD card at address e624
mmcblk0: mmc0:e624 SU02G 1.84 GiB
mmcblk0: p1
mount: mounting /dev/mmcblk0p1 on /r failed: No such device or address
1Wire touchscreen OK
/init: line 103: can't open /r/dev/console: no such file
Kernel panic - not syncing: Attempted to kill init!
[<c016fde8>] (unwind_backtrace+0x0/0xe4) from [<c033e200>] (panic+0x68/0x184)
[<c033e200>] (panic+0x68/0x184) from [<c0180aac>] (do_exit+0x68/0x668)
[<c0180aac>] (do_exit+0x68/0x668) from [<c01813d8>] (do_group_exit+0xb0/0xe4)
[<c01813d8>] (do_group_exit+0xb0/0xe4) from [<c018141c>]
(sys_exit_group+0x10/0x18)
[<c018141c>] (sys_exit_group+0x10/0x18) from [<c016a640>]
(ret_fast_syscall+0x0/0x30)
one_wire_status: 2
U-Boot 1.1.6-ptx-2011.11.0 (Mar 6 2013 - 23:23:16) for FriendlyARM MINI6410
CPU: S3C6410@532MHz
Fclk = 532MHz, Hclk = 133MHz, Pclk = 66MHz, Serial = CLKUART (SYNC
Mode)
Board: MINI6410
DRAM: 256 MB
Flash: 0 kB
NAND: 1024 MB
MMC:
Setting up an SD card with 3862528 sectors:
Useable area ends with sector 3862526.
BL1 area starts in sector 3862510.
Environment area starts in sector 3862254.
BL2 area starts in sector 3861742.
Kernel area starts in sector 3850222.
1887 MB
In: serial
Out: serial
Err: serial
MAC: 08:90:90:90:90:90
Hit any key to stop autoboot: 0
Reading zImage from block 3850222.. Completed!
Boot with zImage
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Initializing cgroup subsys cpu
Linux version 2.6.38 (david@devbox) (gcc version 4.5.1 (ctng-1.8.1-FA) ) #1
PREEMPT Thu Mar 7 01:38:42 EST 2013
CPU: ARMv6-comp: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
Machine: MINI6410
Memory policy: ECC disabled, Data cache writeback
CPU S3C6410 (id 0x36410101)
S3C24XX Clocks, Copyright 2004 Simtec Electronics
camera: no parent clock specified
S3C64XX: PLL settings, A=532000000, M=532000000, E=24000000
S3C64XX: HCLK2=266000000, HCLK=133000000, PCLK=66500000
mout_apll: source is fout_apll (1), rate is 532000000
mout_epll: source is epll (1), rate is 24000000
mout_mpll: source is mpll (1), rate is 532000000
mmc_bus: source is mout_epll (0), rate is 24000000
mmc_bus: source is mout_epll (0), rate is 24000000
mmc_bus: source is mout_epll (0), rate is 24000000
usb-bus-host: source is clk_48m (0), rate is 48000000
uclk1: source is dout_mpll (1), rate is 66500000
spi-bus: source is mout_epll (0), rate is 24000000
spi-bus: source is mout_epll (0), rate is 24000000
audio-bus: source is mout_epll (0), rate is 24000000
audio-bus: source is mout_epll (0), rate is 24000000
audio-bus: source is mout_epll (0), rate is 24000000
irda-bus: source is mout_epll (0), rate is 24000000
camera: no parent clock specified
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65024
Kernel command line: root=/dev/mmcblk0p1 rootwait console=ttySAC0,115200
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 255416k/255416k available, 6728k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xff000000 - 0xffe00000 ( 14 MB)
vmalloc : 0xd0800000 - 0xf6000000 ( 600 MB)
lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc0160000 (1376 kB)
.text : 0xc0160000 - 0xc04005c0 (2690 kB)
.data : 0xc0402000 - 0xc0421fa0 ( 128 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Preemptable hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:246
VIC @f6000000: id 0x00041192, vendor 0x41
VIC @f6010000: id 0x00041192, vendor 0x41
Console: colour dummy device 80x30
console [ttySAC0] enabled
Calibrating delay loop... 530.84 BogoMIPS (lpj=2654208)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registers3c64xx_dma_init: Registering DMA channels
PL080: IRQ 73, at d0808000, channels 0..8
PL080: IRQ 74, at d080c000, channels 8..16
S3C6410: Initialising architecture
bio: create slab <bio-0> at 0
s3c-i2c s3c2440-i2c: slave address 0x10
s3c-i2c s3c2440-i2c: bus frequency set to 64 KHz
s3c-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
NetWinder Floating Point Emulator V0.97 (double precision)
msgmni has been set to 498
io scheduler noop registered (default)
io scheduler cfq registered
S3C_LCD clock got enabled :: 133.000 Mhz
LCD TYPE :: A70 will be initialized
Window[0] - FB1: map_video_memory: clear ff000000:00177000
FB1: map_video_memory: dma=5f000000 cpu=ff000000 size=00177000
Window[0] - FB2: map_video_memory: clear ff0bb800:000bb800
FB2: map_video_memory: dma=5f0bb800 cpu=ff0bb800 size=000bb800
Console: switching to colour frame buffer device 100x30
fb0: s3cfb frame buffer device
backlight initialized
s3c6400-uart.0: ttySAC0 at MMIO 0x7f005000 (irq = 16) is a S3C6400/10
s3c6400-uart.1: ttySAC1 at MMIO 0x7f005400 (irq = 20) is a S3C6400/10
s3c6400-uart.2: ttySAC2 at MMIO 0x7f005800 (irq = 24) is a S3C6400/10
s3c6400-uart.3: ttySAC3 at MMIO 0x7f005c00 (irq = 28) is a S3C6400/10
adc initialized
loop: module loaded
S3C NAND Driver, (c) 2008 Samsung Electronics
S3C NAND Driver is using hardware ECC.
NAND device: Manufacturer ID: 0xec, Chip ID: 0xd3 (Samsung NAND 1GiB 3,3V 8-bit)
Creating 3 MTD partitions on "NAND 1GiB 3,3V 8-bit":
0x000000000000-0x000000080000 : "Bootloader"
0x000000080000-0x000000580000 : "Kernel"
0x000000580000-0x000040000000 : "File System"
dm9000 Ethernet Driver, V1.31
eth0: dm9000a at d081e000,d0c00004 IRQ 108 MAC: 08:90:90:90:90:90 (chip)
mousedev: PS/2 mouse device common for all mice
touchscreen-1wire initialized
backlin Pipe as /devices/virtual/input/input0
ts-if initialized
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
one_wire_status: 4
s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling
s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133000000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133000000 Hz)
one_wire_status: 4
s3c-sdhci s3c-sdhci.0: clock source 2: mmc_bus (24000000 Hz)
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133000000 Hz)
one_wire_status: 4
s3c-sdhci s3c-sdhci.1: clock source 1: hsmmc (133000000 Hz)
s3c-sdhci s3c-sdhci.1: clock source 2: mmc_bus (24000000 Hz)
mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA
TCP cubic registered
NET: Registered protocol family 17
VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
s3c-rtc s3c64xx-rtc: setting system clock to 2013-03-07 17:13:53 UTC
(1362676433)
Freeing init memory: 1376K
mmc0: new SD card at address e624
mmcblk0: mmc0:e624 SU02G 1.84 GiB
mmcblk0: p1
EXT2-fs (mmcblk0p1): warning: mounting unchecked fs, running e2fsck is
recommended
1Wire touchscreen OK
init started: BusyBox v1.20.2 (2013-03-07 01:03:05 EST)
starting pid 382, tty '/dev/console': '/etc/init.d/rcS'
mounting filesystems...done.
running rc.d services...
starting udev
mounting tmpfs at /dev
creating static nodes
starting udevd...done
waiting for devices...done
Console: switching to colour dummy device 80x30
starting network interfaces...
eth0: link down
udhcpc (v1.20.2) started
Sending discover...
eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
Sending discover...
Sending discover...
Sending select for 192.168.1.8...
Lease of 192.168.1.8 obtained, lease time 86400
deleting routers
route: SIOCDELRT: No such process
adding dns 192.168.1.1
Starting telnetd...
Starting NTP server: ntpd ...DONE
loading modules
starting pid 471, tty '/dev/console': '/sbin/getty -L 115200 ttySAC0 vt100'
