Hello, Your log is very disturbing , could it be possible to send your tie point list to test it
Bye 2014/1/19 Mustafa Teke <[email protected]> > Dear Jonathan, > Thanks for you help, put \t helped. > > There is a small point I would like to point out, > input coordinate list is x, y, lon, lat, z > however logger displays x=2886.62, y=2886.62, z=0, lon=2886.62, > lat=2886.62, I hope it is only a textual error, not the error itself. > > I will ask another question in another but in a seperate post. > Best regards > > ps: btw I could not make the software work properly, but it make me > understand when I read the cookbook. > > Mustafa > > On Sunday, January 19, 2014 12:40:55 AM UTC+2, Jonathan Guinet wrote: > >> Hello, >> >> - this cookbook section should help you to ortorectify your image with >> refined geom using extended filenames : >> >> http://www.orfeo-toolbox.org/CookBook/CookBooksu28.html#x45-680003.2.5 >> >> - your input tie points coordinates should be separeted by '\t' (tab) >> character is it the case ? >> >> bye >> >> Jonathan >> >> >> >> >> 2014/1/18 Mustafa Teke <[email protected]> >> >>> Dear all, >>> I wonder that if I generate an RPC model, can I apply the same for other >>> images to orthorectify them? >>> >>> My second question is that when I load my formated tie points, logs >>> display that points are not loaded properly. >>> >>> first 4 lines of my input file: >>> 2886.619385;2525.937744 42.08553696 34.81183624 >>> 3005.132568 2443.451416 42.07795715 34.80993652 >>> 2989.003174 2437.075684 42.07880402 34.8094101 >>> 2969.939941 2541.251953 42.08097458 34.81384659 >>> 3058.988037 2360.797119 42.0740242 34.80699158 >>> >>> Log output: >>> >>> 2014 Jan 18 20:31:23 : Application.logger (INFO) Elevation management: >>> setting default height above ellipsoid to 0 meters >>> >>> 2014 Jan 18 20:31:23 : Application.logger (INFO) Adding tie point >>> x=2886.62, y=2886.62, z=0, lon=2886.62, lat=2886.62 >>> >>> 2014 Jan 18 20:31:23 : Application.logger (INFO) Adding tie point >>> x=3005.13, y=3005.13, z=0, lon=3005.13, lat=3005.13 >>> >>> 2014 Jan 18 20:31:23 : Application.logger (INFO) Adding tie point >>> x=2989, y=2989, z=0, lon=2989, lat=2989 >>> >>> 2014 Jan 18 20:31:23 : Application.logger (INFO) Adding tie point >>> x=2969.94, y=2969.94, z=0, lon=2969.94, lat=2969.94 >>> >>> 2014 Jan 18 20:31:23 : Application.logger (INFO) Adding tie point >>> x=3058.99, y=3058.99, z=0, lon=3058.99, lat=3058.99 >>> >>> -- >>> -- >>> Check the OTB FAQ at >>> http://www.orfeo-toolbox.org/FAQ.html >>> >>> You received this message because you are subscribed to the Google >>> Groups "otb-users" group. >>> To post to this group, send email to [email protected] >>> >>> To unsubscribe from this group, send email to >>> [email protected] >>> >>> For more options, visit this group at >>> http://groups.google.com/group/otb-users?hl=en >>> --- >>> You received this message because you are subscribed to the Google >>> Groups "otb-users" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> >>> For more options, visit https://groups.google.com/groups/opt_out. >>> >> >> -- > -- > Check the OTB FAQ at > http://www.orfeo-toolbox.org/FAQ.html > > You received this message because you are subscribed to the Google > Groups "otb-users" group. > To post to this group, send email to [email protected] > To unsubscribe from this group, send email to > [email protected] > For more options, visit this group at > http://groups.google.com/group/otb-users?hl=en > --- > You received this message because you are subscribed to the Google Groups > "otb-users" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > For more options, visit https://groups.google.com/groups/opt_out. > -- -- Check the OTB FAQ at http://www.orfeo-toolbox.org/FAQ.html You received this message because you are subscribed to the Google Groups "otb-users" group. To post to this group, send email to [email protected] To unsubscribe from this group, send email to [email protected] For more options, visit this group at http://groups.google.com/group/otb-users?hl=en --- You received this message because you are subscribed to the Google Groups "otb-users" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. For more options, visit https://groups.google.com/groups/opt_out.
