On Fri, May 26, 2017 at 10:53:32AM -0400, Russell Bryant wrote: > On Fri, May 26, 2017 at 12:49 AM, Ben Pfaff <[email protected]> wrote: > > It's becoming more common that OSes include "ip" but not "ifconfig", so > > it's best to avoid using the latter. This commit removes most references > > to "ifconfig" and replaces them by "ip". It also adds a build-time check > > to make it harder to introduce new uses of "ifconfig". > > > > Signed-off-by: Ben Pfaff <[email protected]> > > --- > > I tested this via "make check", only. > > v1->v2: Remove unrelated change (thanks Joe!). > > > > Documentation/faq/configuration.rst | 2 +- > > Documentation/faq/issues.rst | 19 +++++++------- > > Documentation/faq/vlan.rst | 6 ++--- > > Documentation/howto/dpdk.rst | 10 ++++---- > > Documentation/howto/kvm.rst | 5 ++-- > > Documentation/ref/ovs-vlan-test.8.rst | 3 ++- > > Documentation/tutorials/ovs-advanced.rst | 11 ++++---- > > Makefile.am | 14 +++++++++++ > > python/ovstest/util.py | 24 +++++++++--------- > > tests/interface-reconfigure.at | 29 > > +++++++++++----------- > > utilities/bugtool/ovs-bugtool.in | 6 ++--- > > utilities/ovs-ofctl.8.in | 4 +-- > > utilities/ovs-vsctl.8.in | 2 +- > > ...ensource_libexec_InterfaceReconfigureVswitch.py | 6 ++--- > > .../opt_xensource_libexec_interface-reconfigure | 4 +-- > > 15 files changed, 79 insertions(+), 66 deletions(-) > > > > diff --git a/Documentation/faq/issues.rst b/Documentation/faq/issues.rst > > index c60336a10569..8ef207bbee6c 100644 > > --- a/Documentation/faq/issues.rst > > +++ b/Documentation/faq/issues.rst > > @@ -43,8 +43,8 @@ eth0. Help! > > itself. For example, assuming that eth0's IP address is > > 192.168.128.5, you > > could run the commands below to fix up the situation:: > > > > - $ ifconfig eth0 0.0.0.0 > > - $ ifconfig br0 192.168.128.5 > > + $ ip addr flush dev eth0 > > + $ ip addr addr 192.168.128.5 dev br0 > > Typo: "ip addr add" > > > @@ -299,13 +299,13 @@ network, but it doesn't work. Why not? > > > > $ ovs-vsctl add-br br0 > > $ ovs-vsctl add-port br0 int0 -- set Interface int0 type=internal > > - $ ifconfig int0 192.168.0.123 > > + $ ip addr addr 192.168.0.123 dev int0 > > and here.
Thanks, I fixed both of these. > > @@ -656,8 +656,8 @@ devices to bridge ``br0``. Once complete, follow the > > below steps: > > > > Configure IP and enable interfaces:: > > > > - $ ifconfig eth0 5.5.5.1/24 up > > - $ ifconfig eth1 90.90.90.1/24 up > > + $ ip addr add 5.5.5.1/24 dev eth0 > > + $ ip addr add 90.90.90.1/24 dev eth1 > > > Is "ip link set eth0 up" needed here too to be equivalent? I am not sure. It cannot hurt, so I added it. _______________________________________________ dev mailing list [email protected] https://mail.openvswitch.org/mailman/listinfo/ovs-dev
