>mab <- without this you wont be doing MAB : ) Otherwise you should be fine, I have been using MAB with Cisco 2960s for years without those commands.
Jake Sallee Godfather of Bandwidth System Engineer University of Mary Hardin-Baylor WWW.UMHB.EDU 900 College St. Belton, Texas 76513 Fone: 254-295-4658 Phax: 254-295-4221 ________________________________________ From: Andrew Lukasiak [[email protected]] Sent: Sunday, September 14, 2014 12:26 PM To: [email protected] Subject: [PacketFence-users] Catalyst 2970 MAC Authentication Hello Everyone, I have been following the excellent Network Devices Configuration Guide to setup Cisco Catalyst 2970 for "MAC Authentication bypass only". The issue is that the interface doesn't want to accept the following commands: authentication periodic authentication timer restart 10800 authentication timer reauthenticate 7200 mab It seems that these options are unavailable. I am running IOS 12.2(44)SE6. I believe it is the most recent one. Would Packetfence work OK with these options left unset? What would be the side effects? I welcome any insights or advice. Thanks. Andrew sw001(config-if)#? Interface configuration commands: arp Set arp type (arpa, probe, snap) or timeout auto Configure Automation bandwidth Set bandwidth informational parameter carrier-delay Specify delay for interface transitions cdp CDP interface subcommands channel-group Etherchannel/port bundling configuration channel-protocol Select the channel protocol (LACP, PAgP) dampening Enable event dampening default Set a command to its defaults delay Specify interface throughput delay description Interface specific description down-when-looped Force looped interface down duplex Configure duplex operation. exit Exit from interface configuration mode flowcontrol Configure flow operation. help Description of the interactive help system hold-queue Set hold queue depth ip Interface Internet Protocol config commands keepalive Enable keepalive l2protocol-tunnel Tunnel Layer2 protocols lacp LACP interface subcommands link Configure Link load-interval Specify interval for load calculation for an interface logging Configure logging for interface mac MAC interface commands macro Command macro max-reserved-bandwidth Maximum Reservable Bandwidth on an Interface mdix Set Media Dependent Interface with Crossover mls mls interface commands mvr MVR per port configuration no Negate a command or set its defaults pagp PAgP interface subcommands priority-queue Priority Queue queue-set Choose a queue set for this queue rmon Configure Remote Monitoring on an interface service-policy Configure QoS Service Policy shutdown Shutdown the selected interface small-frame Set rate limit parameters for small frame snmp Modify SNMP interface parameters source Get config from another source spanning-tree Spanning Tree Subsystem speed Configure speed operation. srr-queue Configure shaped round-robin transmit queues storm-control storm configuration switchport Set switching mode characteristics timeout Define timeout values for this interface transmit-interface Assign a transmit interface to a receive-only interface tx-ring-limit Configure PA level transmit ring limit udld Configure UDLD enabled or disabled and ignore global UDLD setting sw001(config-if)#dot1x ? auth-fail Configure Authentication Fail values for this port control-direction Set the control-direction on the interface critical Enable 802.1x Critical Authentication default Configure Dot1x with default values for this port fallback Enable the Webauth fallback mechanism guest-vlan Configure Guest-vlan on this interface host-mode Set the Host mode for 802.1x on this interface mac-auth-bypass Enable MAC Auth Bypass max-reauth-req Max No.of Reauthentication Attempts max-req Max No.of Retries pae Set 802.1x interface pae type port-control set the port-control value reauthentication Enable or Disable Reauthentication for this port timeout Various Timeouts violation-mode Set the Security Violation mode on this interface ------------------------------------------------------------------------------ Want excitement? Manually upgrade your production database. When you want reliability, choose Perforce Perforce version control. Predictably reliable. http://pubads.g.doubleclick.net/gampad/clk?id=157508191&iu=/4140/ostg.clktrk _______________________________________________ PacketFence-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/packetfence-users ------------------------------------------------------------------------------ Want excitement? Manually upgrade your production database. When you want reliability, choose Perforce Perforce version control. Predictably reliable. http://pubads.g.doubleclick.net/gampad/clk?id=157508191&iu=/4140/ostg.clktrk _______________________________________________ PacketFence-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/packetfence-users
