Hello Safiullah,


Le 2017-03-18 à 13:55, Safiullah Tariq a écrit :
Hello All,

I hope you are doing great.

I have installed PacketFence and used Out-of-Band implementation. I have done exactly what the guide says. However, I am still not able to get anything working.

According to the guide, I have done the settings on Mikrotik, which was not an issue for me, now comes the hard part. I have a system with 5 LAN ports, I have setup Management on one and other such as Registration and Isolation on the other ports.

Do you mean the Mikrotik switch ?
Management IP is 10.2.2.88 (on LAN1)
Registration IP is 192.168.2.1/24 <http://192.168.2.1/24> (On LAN port 2) (VLAN ID= 2) Isolation IP is 192.168.3.1/24 <http://192.168.3.1/24> (On LAN port 2) (VLAN ID= 3)
IP to the Port without vlan 192.168.1.5 (on Lan port 2)


1. I dont know what is Normal VLAN as it doesn't show in the drop down menu.
A normal vlan is in fact a production vlan where you have your own dhcp/dns/gateway, for PacketFence it's just a vlan id
2. The management interface does not have DHCP option.
Yes this is correct, this interface is use to talk to your switch/AP (radius/snmp/...)
3. In the document, there is nothing mentioned about the IP scheme of mikrotik.
Think simple, one ip address where you can ping packetfence management ip address and other vlan managed by pf (reg/isol) and multiples normal vlan (your prod)
4. Still i gave 192.168.1.6 ip to mikrotik's port which is connecting to the PF. As the out-of-band document says that Radius ip should be 192.168.1.5. I am not able to ping PF from mikrotik or mikrotik from PF.
You need to fix that, let's say it's on the same layer 2 network then you need to be able to ping each other.
5. Should I move all the VLANs to the management port ?
Why not, it depend of your infra.
Let say that on PacketFence you have an interface eth0 and it's directly connected on the Mikrotik port, so if you tag vlan 2 and vlan 3 and have native vlan 1 on the mikrotik side then on the Pf side you should have eth0 (vlan1) , eth0.2 (vlan2) and eth0.3 interface.

Also if you have more interface on the pf side eth0 eth1 eth2 then you can plug eth0 to the mgmt interface (mikrotik), eth1 on the Reg interface (mikrotik reg int) and eth2 to the isol interface.

It's an example but keep in mind that pf reg interface must ping mikrotik reg ip, isol ... mgmt ...
6. Should I setup DHCP in mikrotik ?

Yes for the normal vlan, not for reg and isol (this is managed by PacketFence)
Regards
Fabrice

I would like to mention here that I want to setup an out of band hotspot wifi

Please do reply as I am sure that your emails will be very helpful.

Regards,


Safiullah Tariq


PRIVILEGED AND CONFIDENTIAL INFORMATION: This e-mail and attachments, if any, may contain confidential and/or proprietary information. Please be advised that the unauthorized use or disclosure of the information is strictly prohibited. The information herein is intended only for use by the intended recipient(s) named above. If you have received this transmission in error, please notify the sender immediately and permanently delete the e-mail and any copies, printouts or attachments thereof.


------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, Slashdot.org! http://sdm.link/slashdot


_______________________________________________
PacketFence-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/packetfence-users

------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, Slashdot.org! http://sdm.link/slashdot
_______________________________________________
PacketFence-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/packetfence-users

Reply via email to