From: Fergal Moran
Lam,
Thanks for your response. Unfortunately the filenames were consistent
throughout <MyApp.tmp/prc> as I remember checking this. However I had up
until now been struggling with the full release of CW6 (constructor
crashing, debug problems etc..) and had installed Lite to see if it was any
more stable. In a fit of rage lastnight I reformatted my hard disk,
reinstalled NT WS and reinstalled the full version of CW6 and everything
has been working beautifully since. So perhaps the problem was something
machin specific.
Regards,
Fergal.
"Jun-Kiat Lam" <[EMAIL PROTECTED]> on 24/01/2000 23:08:17
Please respond to "Palm Developer Forum" <[EMAIL PROTECTED]>
To: "Palm Developer Forum" <[EMAIL PROTECTED]>
cc: (bcc: Fergal Moran/962264/Ireland/Europe/EKC)
Subject: Re: Beginner & stationary
>From the description, I think the problem is caused by differences in the
name of the output file expected by the PalmRez Post Linker and the actual
output file name as specified in the 68K Target panel. The New Project
wizard in CW Lite attempts to name the 68K Target output file name to be
same as your project name. However, this causes problems in the PalmRez
Post
Linker panel Mac Resource File field as it is not changed. In your case, it
appears that PalmRez is sucking in Starter.tmp instead of <your project
name>.tmp. To resolve it, change either the 68K Target panel or PalmRez
Post
Linker panel file name such that they are both the same i.e. <Your project
name>.tmp. This should fix it.
Rgds,
Jun-Kiat Lam
Metrowerks Technical Support
----- Original Message -----
From: <[EMAIL PROTECTED]>
To: "Palm Developer Forum" <[EMAIL PROTECTED]>
Sent: Monday, January 24, 2000 6:28 AM
Subject: Beginner & stationary
>
>
> From: Fergal Moran
> Hi all,
> Forgive obvious beginner questions but I have spent the morning on the
3com
> and metrowerks sites looking for answers.
>
> I have created a new application with CW Lite using the 3.1 stationery.
> I am trying to add a custom about screen and have opened the .rsrc file
in
> the constructor and created a new form.
> Then I modified the MainFormDoCommand handler and removed the line
>
> AbtShowAbout (appFileCreator);
>
> and added the lines
> FormPtr frm;
> frm = FrmInitForm(AboutForm);
> FrmDoDialog(frm);
>
> However when I make and debug the application I still
> get the original about form. I have stepped
> through the code and the modified handler
> is being called with the modified lines of code.
> I have also checked the .h file and AboutForm is
> in their with a correct and unique ID.
>
> Curious - I tried adding another item to the mainform
> menu as documented in the MemoPad tutorial and this did
> not show up either when I re-built and debugged the app
> there was again no show.
>
> What am I doing wrong folks?
>
> Regards,
>
> Fergal.
>
>
>
>
>
> ---
> You are currently subscribed to palm-dev-forum as: [EMAIL PROTECTED]
> To unsubscribe send a blank email to
[EMAIL PROTECTED]
> For more information on the Palm Developer Forum's, see
<http://www.palm.com/devzone/mailinglists.html>
>
---
For information on using the Palm Developer Forums, or to unsubscribe,
please see <http://www.palm.com/devzone/mailinglists.html>.
---
For information on using the Palm Developer Forums, or to unsubscribe, please see
<http://www.palm.com/devzone/mailinglists.html>.
