I don't have an explanation. I'm hoping you can use the debugger to provide some more information.
-Ken > -----Original Message----- > From: Dominik Szczerba [mailto:[EMAIL PROTECTED] > Sent: Tuesday, September 02, 2008 9:45 AM > To: Moreland, Kenneth > Cc: [email protected] > Subject: Re: [Paraview] requesting particular animation frame > > Thanks for a hint, but how do you explain that the problem happens only > after > an animation has been generated? It does not occur before, a frame is > reached > in one precise jump. --Dominik > > On Tuesday 02 September 2008 04:18:34 pm Moreland, Kenneth wrote: > > None of the filters you mention should effect the pipeline time and I > still > > cannot replicate your problem. I was using the exodus reader, so it > could > > be a problem with whatever reader you are using. Perhaps you could add > > breakpoints to the RequestInformation and RequestData methods to see > check > > the times being requested. > > > > -Ken > > > > > -----Original Message----- > > > From: Dominik Szczerba [mailto:[EMAIL PROTECTED] > > > Sent: Tuesday, September 02, 2008 7:44 AM > > > To: Moreland, Kenneth > > > Cc: [email protected] > > > Subject: Re: [Paraview] requesting particular animation frame > > > > > > Indeed, it is a pipeline: cut, calculator, surface vectors and two > > > streamline > > > filters at the end. Requesting specific time steps results in going > > > through > > > all the intermediate steps, which can take a very long time. > > > > > > However! This seems to only happen AFTER an animation was generated > (as > > > png > > > images). So likely something is broken here. Can someone confirm > please? > > > > > > -- Dominik > > > > > > On Tuesday 02 September 2008 03:16:58 pm Moreland, Kenneth wrote: > > > > I am not seeing that behavior in either the 3.2 release or the CVS > > > > > > version. > > > > > > > As far as I can tell, ParaView is correctly requesting a single > time > > > > > > step > > > > > > > from the pipeline. If you have other filters, it is possible that > some > > > > > > of > > > > > > > them are requesting multiple time steps. It is also possible to get > > > > "thrashing" behavior if you have a branching pipeline and the > branches > > > > > > are > > > > > > > requesting different time steps. > > > > > > > > -Ken > > > > > > > > > -----Original Message----- > > > > > From: [EMAIL PROTECTED] > > > > > [mailto:[EMAIL PROTECTED] On Behalf Of Dominik > Szczerba > > > > > Sent: Monday, September 01, 2008 3:03 PM > > > > > To: [email protected] > > > > > Subject: [Paraview] requesting particular animation frame > > > > > > > > > > I just noticed that requesting an animation frame (by entering a > > > > > > number > > > > > > > > or using << >> buttons) does so by walking (loading) all the > frames > > > > > > one > > > > > > > > by one > > > > > from a current one until the desired one is reached. Did I screw > > > > > something in > > > > > the RequestInformation / Update of my Reader? > > > > > Thanks for any hints. > > > > > -- > > > > > Dominik Szczerba, Ph.D. > > > > > Computational Physics Group > > > > > Foundation for Research on Information Technologies in Society > > > > > http://www.itis.ethz.ch > > > > > _______________________________________________ > > > > > ParaView mailing list > > > > > [email protected] > > > > > http://www.paraview.org/mailman/listinfo/paraview > > > > > > -- > > > Dominik Szczerba, Ph.D. > > > Computational Physics Group > > > Foundation for Research on Information Technologies in Society > > > http://www.itis.ethz.ch > > > > -- > Dominik Szczerba, Ph.D. > Computational Physics Group > Foundation for Research on Information Technologies in Society > http://www.itis.ethz.ch _______________________________________________ ParaView mailing list [email protected] http://www.paraview.org/mailman/listinfo/paraview
