Both scenarios are wrong. ParaView will not push out data from process 0 to processes 1-3 unless you explicitly run a filter that does that (or the reader does that internally, but I know of no such reader). What is actually happening is more along the lines of:
1. Processes 0-3 each read in a partition of data from the file. 2. Each process extracts polygonal geometry from their local data. 3. Per your settings, ParaView decides to send the geometry to the client. The data is collected to process 0 and sent to the client. The reason you are not seeing vtkFileSeriesReader on all of the servers is that there is a threshold in the timer log to not show anything that executes under a certain amount of time (by default 0.01 seconds). If you change the Time Threshold to Show All, you should be able to see everything that executes, even if it completes immediately. You should note that how readers read partitions is determined by the reader itself. Many of the readers do not really handle partitioned reading. Thus, the reader will do something naïve like read everything on process 0. Based on your timings, that is probably what is happening to you. That is, processes 1-3 probably have empty data. You never specified what format of data you are reader, so I cannot answer the data completely. However, if you want to know how your data is partitioned on the server (at least, before rendering), you can run the Process Ids filter. -Ken On 9/24/09 9:09 PM, "chew ping" <[email protected]> wrote: Hi all, I'm doing parallel rendering using 1 client (dual core laptop) and 2 cluster servers (dual core desktop) below is the timer log result i collected when i run: mpirun -np 4 pvserver ----------------------------------------------------------------------------------------------- Local Process Still Render, 3.029 seconds Execute vtkMPIMoveData id: 457, 1.98248 seconds Server, Process 0 Execute vtkFileSeriesReader id: 176, 0.637821 seconds Execute vtkMPIMoveData id: 457, 1.49186 seconds Dataserver gathering to 0, 0.829525 seconds Dataserver sending to client, 0.661658 seconds Server, Process 1 Execute vtkMPIMoveData id: 457, 0.141821 seconds Dataserver gathering to 0, 0.141544 seconds Server, Process 2 Execute vtkMPIMoveData id: 457, 0.243584 seconds Dataserver gathering to 0, 0.243318 seconds Server, Process 3 Execute vtkMPIMoveData id: 457, 0.191589 seconds Dataserver gathering to 0, 0.191303 seconds ----------------------------------------------------------------------------------------------------- i have difficulty interpreting the timer log, my guess is: Scenario 1: Process 0 reads the whole data, disseminate the dats into 4 pieces, then distribute to itself and Process 1&2&3, each node will process the data and send it back Process 0, Process 0 gather all data and send it back to client, client renders the data Scenario 2: Process 0 reads the whole data, distribute the whole data to Process 0&1&2&3, each node will 'take' their own piece of data to process, then send it back Process 0, Process 0 gather all data and send it back to client, client renders the data Which scenario is the correct one? or both are wrong? is there any resources i could refer to find what does it mean by: Execute vtkFileSeriesReader, Execute vtkMPIMoveData? any help / feedback is highly appreciated! thanks! regards, chewping **** Kenneth Moreland *** Sandia National Laboratories *********** *** *** *** email: [email protected] ** *** ** phone: (505) 844-8919 *** web: http://www.cs.unm.edu/~kmorel
_______________________________________________ Powered by www.kitware.com Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html Please keep messages on-topic and check the ParaView Wiki at: http://paraview.org/Wiki/ParaView Follow this link to subscribe/unsubscribe: http://www.paraview.org/mailman/listinfo/paraview
