I'm not sure what version of CMake the HDF5-CMake project requires. I
was coding all of my stuff to CMake 2.6 then the last time I pulled
the HDF5-CMake sources there was the Cmake 2.8 Min requirement. So
don't know.
___________________________________________________________
Mike Jackson www.bluequartz.net
Principal Software Engineer [email protected]
BlueQuartz Software Dayton, Ohio
On Apr 28, 2010, at 12:51 PM, Biddiscombe, John A. wrote:
And bear in mind that once I am confident enough to push git
nonsense to kitware and everywhere else, then I'll be upgrading the
hdf5 in paraview to 1.8
And that is before paraview 3.10, it will be on the 3.8.x something
release.
Actually Mike, doesn't our hdf5 require cmake 1.8 anyway?
in which case we should make the cmake switch in paraview, I'd
forgotten about that.
On the dev list, upgrading hdf5 was agreed, but the cmake change was
not.
Comments?
JB
-----Original Message-----
From: [email protected] [mailto:[email protected]
]
On Behalf Of Dave Partyka
Sent: 28 April 2010 18:33
To: Michael Jackson
Cc: ParaView list
Subject: Re: [Paraview] ParaView 3.8 RC1 needs more elaborate
FindHDF5.cmake
True, I can copy the CMake version onto the branch if that sounds
reasonable? Let me consult with my spiritual advisors first before
I commit
to anything. ;-)
On Wed, Apr 28, 2010 at 12:29 PM, Michael Jackson
<[email protected]> wrote:
Right, In CMake 2.8.1, I Checked. I'll assume that you are NOT going
to switch the ParaView 3.8 branch from Cmake 2.6.x to CMake 2.8
BEFORE it is
released which would be a pretty large last minute change.
So basically, for the ParaView 3.8 branch this will be left
unfixed?
I just need to know how I am going to formulate my work-around
until PV 3.10
is released.
--
Mike Jackson
On Apr 28, 2010, at 12:22 PM, Dave Partyka wrote:
There is a FindHDF5 that is built into CMake, I think 2.8, that
was re-written and vastly improved in the not so distant past. When
we
switch VTK/ParaView to require CMake 2.8 we can remove the one in
ParaView
which will then use the one included in CMake. I haven't gotten the
go ahead
but it is something we will probably do very soon.
On Wed, Apr 28, 2010 at 12:00 PM, Michael Jackson
<[email protected]> wrote:
I am having a problem building ParaView against a prebuilt HDF5
library. I set the PARAVIEW_USE_SYSTEM_HDF5=ON during the initial
CMake
Configuration. The problem is that FindHDF5.cmake that is included
with
ParaView is pretty basic and can not find the HDF5 that is
installed on my
system.
Can we possibly include a file with a bit more searching
capabilities? I have a candidate that I think will work (works with
my
projects) or is there a way to over-ride the CMAKE_MODULE_PATH from
the
command line?
This is on Windows with Visual Studio (64 bit if it really
matters)
___________________________________________________________
Mike Jackson www.bluequartz.net
Principal Software Engineer [email protected]
BlueQuartz Software Dayton, Ohio
_______________________________________________
Powered by www.kitware.com
Visit other Kitware open-source projects at
http://www.kitware.com/opensource/opensource.html
Please keep messages on-topic and check the ParaView Wiki at:
http://paraview.org/Wiki/ParaView
Follow this link to subscribe/unsubscribe:
http://www.paraview.org/mailman/listinfo/paraview
