Richard & Adriano, I am absolutely certain that the file is actually a data file .plt. I am also sure that the file is valid for tecplot (it loaded into tecplot). I can send you a sample file if that would be informative.
Chris Butler On 24/03/2011, at 9:02 PM, Adriano Gagliardi wrote: > > Just to be sure, this is a Tecplot .tec or .dat file we are talking about, > and not a .lpk or .lay file? > > > =================================== > > Adriano Gagliardi MEng PhD > Business Sector Leader > Computational Aerodynamics > Aircraft Research Association Ltd. > Manton Lane > Bedford > > Tel: 01234 32 4644 > E-mail: [email protected] > Url: www.ara.co.uk > -----Original Message----- > From: [email protected] [mailto:[email protected]] > On Behalf Of Richard GRENON > Sent: 24 March 2011 08:40 > To: Christopher Butler > Cc: [email protected] > Subject: Re: [Paraview] Tecplot binary reader failure /limitations (3.10.0) > > Hi Chris. > > I tried to write Tecplot binary files with Tecplot 360 2009 and Tecplot 360 > 2010, and both saved files have the same version number #!TDV112 and they > can be loaded with PV 3.10.0. > > But an old Tecplot binary file with the version number #!TDV71 can also be > loaded with PV 3.10.0. ! > > So the Tecplot version number does not seem to be the problem, at least from > 71 to 112. Could your original file have been corrupted ? > > Richard. > > > Christopher Butler a écrit : >> Hi Richard, >> Downloaded the linux binaries again, however, I had the same issue. > However, I had access to a version of tecplot (tec360 (2009)) and saved the > file as an updated version. This version then loaded into Paraview. >> >> The original file had a tecplot version string of #!TDV102 compared with > #!TDV112. Therefore I guess there is a limitation on the versions of tecplot > files that are accepted by the reader. >> >> Regards, >> Chris Butler >> > -- > Richard GRENON > ONERA > Departement d'Aerodynamique Appliquee - DAAP/ACI > 8 rue des Vertugadins > 92190 MEUDON - FRANCE > phone : +33 1 46 73 42 17 > fax : +33 1 46 73 41 46 > mailto:[email protected] > http://www.onera.fr > > _______________________________________________ > Powered by www.kitware.com > > Visit other Kitware open-source projects at > http://www.kitware.com/opensource/opensource.html > > Please keep messages on-topic and check the ParaView Wiki at: > http://paraview.org/Wiki/ParaView > > Follow this link to subscribe/unsubscribe: > http://www.paraview.org/mailman/listinfo/paraview > > > ********************************************************************** > This email contains information that is private and confidential and is > intended only for the addressee. > If you are not the intended recipient please delete it and notify us > immediately by e-mailing the sender. > Note: All email sent to or from this address may be accessed by someone other > than the recipient, for > system management and security reasons. > Aircraft Research Association Ltd. Registered in England, Registration No > 503668 Registered Office: > Manton Lane, Bedford MK41 7PF England VAT No GB 196351245 > > ********************************************************************** Chris Butler Ph.D. Candidate Dept. Mechanical and Aerospace Engineering Building 31 Monash University, VIC, 3800 Phone (W): +61 (0)3 990 51617 Phone (M): +61 (0)4083890624 Email (W): [email protected] Email (P): [email protected] _______________________________________________ Powered by www.kitware.com Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html Please keep messages on-topic and check the ParaView Wiki at: http://paraview.org/Wiki/ParaView Follow this link to subscribe/unsubscribe: http://www.paraview.org/mailman/listinfo/paraview
