Ooops thanks for the hint. I did a test with a very basic setup, and reloading the state worked just fine. Hopefully, that was not only coincidence.
Thanks again, Christoph Von: [email protected] [mailto:[email protected]] Im Auftrag von Chr. Rossmanith Gesendet: Dienstag, 15. Mai 2012 08:19 An: [email protected] Betreff: Re: [Paraview] Problems loading saved states Maybe the ° in °C is causing the trouble? Christina Am 14.05.2012 16:34, schrieb Christoph Meyer: Please find a little sample attached. The message I get when trying to open it is this here: ERROR: In ..\..\..\..\src\VTK\IO\vtkXMLParser.cxx, line 483 vtkPVXMLParser (000000000C09BE60): Error parsing XML in stream at line 3771, column 35, byte index 186690: not well-formed (invalid token) Root does not exist. Either state file could not be opened or it does not contain valid xml Looking at the pvsm file in the appropriate line, I don't understand all of it, but can't see anything suspicious either. -----Ursprüngliche Nachricht----- Von: Sebastien Jourdain [mailto:[email protected]] Gesendet: Montag, 14. Mai 2012 16:02 An: Christoph Meyer Cc: [email protected] Betreff: Re: [Paraview] Problems loading saved states You can try to look at your pvsm file and see if you find something suspicious. Otherwise, if you can share the state file without the data, you can send it to us so we can try to track the problem down. Seb On Mon, May 14, 2012 at 9:30 AM, Christoph Meyer <mailto:[email protected]> <[email protected]> wrote: No, not that I am aware of. We do have those weird special chars in German (ä, ö, ü, ß), which I've learned long ago better to avoid in technical software. And I did, as far as I can see. But, since you mention it, I did at one point have the feeling, that ParaView doesn't treat the german standard notation for decimal numbers (decimal comma, separator point) consistently. My system is set to that format, but (most, possibly not all) numbers in ParaView's menus appear in anglo-saxon notation (decimal point). Unfortunately, I can't find an example for exceptions right now. Could that be something? -----Ursprüngliche Nachricht----- Von: Sebastien Jourdain [mailto:[email protected]] Gesendet: Montag, 14. Mai 2012 15:17 An: Christoph Meyer Cc: [email protected] Betreff: Re: [Paraview] Problems loading saved states Is it possible that you have some non-ascii chars in your state file that could come from your field data ? On Mon, May 14, 2012 at 4:51 AM, Christoph Meyer <mailto:[email protected]> <[email protected]> wrote: Hello everyone around. as a newbie to this list and a relative beginner with ParaView Im glad to have found you, and very relieved by the prospect of possibly getting some help for my present problems with ParaView. Apologies in advance, in case my beginner-questions should turn out to be quite basic. Most pressing problem is, that my installation (ParaView 3.14.1 64 bit, running on WIN7) is extremely unreliable, when it comes to loading saved states. In fact, that works very rarely. Most of the times, I get error messages similar to this one ERROR: In ..\..\..\..\src\VTK\IO\vtkXMLParser.cxx, line 483 vtkPVXMLParser (000000000C1412F0): Error parsing XML in stream at line 2149, column 35, byte index 109506: not well-formed (invalid token) Root does not exist. Either state file could not be opened or it does not contain valid xml There is no indication of any problems while working with ParaView or when saving a state. I dont think Im using any exotic filters (ENSIGHT-reader, calculator, slices etc.). The crash occurs before Im asked which data file to read, right after picking a *.pvsm file to load. I will now try to work around the problem by tracing my work, but would very much prefer a proper start from a saved state. Any hint on possible solution will be very much appreciated. Regards Chris _______________________________________________ Powered by www.kitware.com Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html Please keep messages on-topic and check the ParaView Wiki at: http://paraview.org/Wiki/ParaView Follow this link to subscribe/unsubscribe: http://www.paraview.org/mailman/listinfo/paraview > _______________________________________________ Powered by www.kitware.com Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html Please keep messages on-topic and check the ParaView Wiki at: http://paraview.org/Wiki/ParaView Follow this link to subscribe/unsubscribe: http://www.paraview.org/mailman/listinfo/paraview
_______________________________________________ Powered by www.kitware.com Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html Please keep messages on-topic and check the ParaView Wiki at: http://paraview.org/Wiki/ParaView Follow this link to subscribe/unsubscribe: http://www.paraview.org/mailman/listinfo/paraview
