Hi Cory, thank you for the hint. However, I don't know how to make a mesh generated by Salomé a multi-block dataset. Could you tell me more or give me a pointer on where I can find that out?
Thanks, Matthias > -----Ursprüngliche Nachricht----- > Von: Cory Quammen [mailto:[email protected]] > Gesendet: Dienstag, 14. Juni 2016 14:27 > An: Zenker, Dr. Matthias > Cc: [email protected] > Betreff: Re: [Paraview] display boundaries of 2D geometry > > Hi Matthais, > > People typically use multi-block data sets for this purpose. ParaView has a > multi-block inspector that enables you change the visibility of the blocks in > a > data set. If you make each surface a block, then you can show/hide each at > will. > > HTH, > Cory > > On Tue, Jun 14, 2016 at 1:11 PM, Zenker, Dr. Matthias > <[email protected]> wrote: > > Hi Cory, > > > > this helped indeed, thank you. > > I load the mesh.vtu file and apply the Threshold filter on the GeometryID, > and display that together with my simulation results. That works fine. > > If I want to display several parts selectively, I can use several > > Thresholds, > which is a bit clumsy. > > It would be nice to be able to get a list of all GeometryIDs, and to check > those which I want displayed. Do you know if there is a way to do that? Or on > a more general basis: are there other, more elegant ways to display a > geometry in ParaView? > > > > Thanks again, > > > > Matthias > > > > > >> -----Ursprüngliche Nachricht----- > >> Von: Cory Quammen [mailto:[email protected]] > >> Gesendet: Montag, 13. Juni 2016 22:28 > >> An: Zenker, Dr. Matthias > >> Cc: [email protected] > >> Betreff: Re: [Paraview] display boundaries of 2D geometry > >> > >> Matthias, > >> > >> I'm not sure I fully understand exactly what you are trying to do, > >> but I will try to make a suggestion anyway. If the edges have a cell > >> data array giving the ID, you should be able to use the Threshold > >> filter to extract the edges associated with a particular body ID. > >> Just set the threshold values to the ID you want to see. > >> > >> Hope that helps, > >> Cory > >> > >> On Mon, Jun 13, 2016 at 6:43 PM, Zenker, Dr. Matthias > >> <[email protected]> wrote: > >> > Hi, > >> > > >> > > >> > > >> > is there a way to display the boundaries (edges) of a 2D geometry? > >> > I have converted my mesh to vtu using Elmergrid, so I have the IDs > >> > of bodies (=surfaces in 2D) and boundaries (edges) in a vtu file. > >> > Can I just display the edges having the same ID? The extract edges filter > does not help. > >> What > >> > else could I try? > >> > > >> > > >> > > >> > Thank you for a helpful hint, > >> > > >> > > >> > > >> > Matthias > >> > > >> > ________________________________ > >> > > >> > Erbe Elektromedizin GmbH Firmensitz: 72072 Tuebingen > >> Geschaeftsfuehrer: > >> > Christian O. Erbe, Reiner Thede Registergericht: Stuttgart HRB > >> > 380137 > >> > > >> > > >> > _______________________________________________ > >> > Powered by www.kitware.com > >> > > >> > Visit other Kitware open-source projects at > >> > http://www.kitware.com/opensource/opensource.html > >> > > >> > Please keep messages on-topic and check the ParaView Wiki at: > >> > http://paraview.org/Wiki/ParaView > >> > > >> > Search the list archives at: http://markmail.org/search/?q=ParaView > >> > > >> > Follow this link to subscribe/unsubscribe: > >> > http://public.kitware.com/mailman/listinfo/paraview > >> > > >> > >> > >> > >> -- > >> Cory Quammen > >> R&D Engineer > >> Kitware, Inc. > > ________________________________ > > > > Erbe Elektromedizin GmbH Firmensitz: 72072 Tuebingen > > Geschaeftsfuehrer: Christian O. Erbe, Reiner Thede Registergericht: > > Stuttgart HRB 380137 > > > > > > -- > Cory Quammen > R&D Engineer > Kitware, Inc. ________________________________ Erbe Elektromedizin GmbH Firmensitz: 72072 Tuebingen Geschaeftsfuehrer: Christian O. Erbe, Reiner Thede Registergericht: Stuttgart HRB 380137 _______________________________________________ Powered by www.kitware.com Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html Please keep messages on-topic and check the ParaView Wiki at: http://paraview.org/Wiki/ParaView Search the list archives at: http://markmail.org/search/?q=ParaView Follow this link to subscribe/unsubscribe: http://public.kitware.com/mailman/listinfo/paraview
