Ridgh I do not believe you can "export" the files you must "generate" them. in 2004 you can create a "job file" then go to the gerber section and add the layers you want to create also create a drill file and any other files. Gerbers are created not "exported" or "saved as".
In 99 you go to "file" "new" "cam output configuration" quite similar to the "job file" above again you need to make choices about layers etc. In 98 you go to "file" "setup printer" "protel Gerber rs274" then fill in the layers and other options you need. Also you need to then run the NC drill under "reports" Good luck Fran -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Ridgh Sent: Wednesday, June 27, 2007 3:45 PM To: 'Protel EDA Discussion List' Subject: Re: [PEDA] Need help to convert .pcbdoc to Gerber files Hello again, First, I'd like to thank you very much for your response. In any case, the only way I found was to convert the files to the old Protel 99 .PCB format, and then to export them with the extensions GBL, GTL, GTO, GBO,.. But checking them with the Camtastic, all I saw on my monitor was a very distorted "draw" - and not the Gerber as I knew before. In any case I'd like to thank you again, Ridgh -----Original Message----- From: Mira [mailto:[EMAIL PROTECTED] Sent: Wednesday, June 27, 2007 5:06 PM To: Protel EDA Discussion List Subject: Re: [PEDA] Need help to convert .pcbdoc to Gerber files Ridgh, If you've managed to generate the gerbers, they are probably saved on your hard drive. Look for file names as your PCB and extensions GBL, GTL, GTO, GBO.. They are automatically open in Camtastic, which is the gerber viewer. If you like to save them from there, you have to use File/Export gerber (not File/Save). To generate the drill file look for NC Drill files. The drill file normally has DRL extension but in Altium designer it's TXT. I'm not sure how the output files are set & generated in DXP-2004 version but to do this in Altium Designer 6.7 you have to create an output job file and run the batch from there. Mira --- Ridgh <[EMAIL PROTECTED]> wrote: > Hello, > I need very much your help: > I am relative newbie in PCB production. > At my new workplace is installed Protel DXP 2004. > Usually I use to draw 1 > layer PCBs and sometimes 2 layers. The output files I'm getting are > .PcbDoc files. > I've been asked to send for production Gerber files, so I've tried the > option Export->Gerber. It opened another window, named "Camtastic" and > got a file with the .CAM . > The problem is that any PCB manufacturer I've asked doesn't know this > format, so, as I assume that you are the professional ones, I'll be > very thankful for your help. > How can I convert it to Gerber files? All I need is a top, mechanical, > solder mask and drilling layers. > Thank you in advance, > Ridgh > > > ____________________________________________________________ > You are subscribed to the PEDA discussion forum > > To Post messages: > mailto:[email protected] > > Unsubscribe and Other Options: > http://techservinc.com/mailman/listinfo/peda_techservinc.com > > Browse or Search Old Archives (2001-2004): > http://www.mail-archive.com/[EMAIL PROTECTED] > > Browse or Search Current Archives (2004-Current): > http://www.mail-archive.com/[email protected] > > ____________________________________________________________________________ ________ Be a better Heartthrob. Get better relationship answers from someone who knows. Yahoo! Answers - Check it out. http://answers.yahoo.com/dir/?link=list&sid=396545433 ____________________________________________________________ You are subscribed to the PEDA discussion forum To Post messages: mailto:[email protected] Unsubscribe and Other Options: http://techservinc.com/mailman/listinfo/peda_techservinc.com Browse or Search Old Archives (2001-2004): http://www.mail-archive.com/[EMAIL PROTECTED] Browse or Search Current Archives (2004-Current): http://www.mail-archive.com/[email protected] ____________________________________________________________ You are subscribed to the PEDA discussion forum To Post messages: mailto:[email protected] Unsubscribe and Other Options: http://techservinc.com/mailman/listinfo/peda_techservinc.com Browse or Search Old Archives (2001-2004): http://www.mail-archive.com/[EMAIL PROTECTED] Browse or Search Current Archives (2004-Current): http://www.mail-archive.com/[email protected] No virus found in this outgoing message. Checked by AVG. Version: 7.5.476 / Virus Database: 269.9.10/873 - Release Date: 6/26/2007 11:54 PM ____________________________________________________________ You are subscribed to the PEDA discussion forum To Post messages: mailto:[email protected] Unsubscribe and Other Options: http://techservinc.com/mailman/listinfo/peda_techservinc.com Browse or Search Old Archives (2001-2004): http://www.mail-archive.com/[EMAIL PROTECTED] Browse or Search Current Archives (2004-Current): http://www.mail-archive.com/[email protected]
