SMART pokazuje że oba dyski zdrowe ?
A jak to sprawdzić ?
smartctl -a /dev/sd?
Wywalił mi 5 stron A4.
Może pokaż?
Czego szukać ? ;-]
FAILING NOW przy własnościach ;)
Proszę ;-)
[root@dns2 ~]# smartctl -a /dev/sdb
smartctl 6.3 2014-07-26 r3976 [i686-linux-4.2.3-1] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Constellation ES.3
Device Model: ST1000NM0033-9ZM173
Serial Number: Z1W4LR7G
LU WWN Device Id: 5 000c50 0873b1bab
Firmware Version: SN04
User Capacity: 1,000,204,886,016 bytes [1,00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Wed Nov 4 13:28:13 2015 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART Status command failed
Please get assistance from http://smartmontools.sourceforge.net/
Register values returned from SMART Status command are:
ERR=0x00, SC=0x00, LL=0x00, LM=0x00, LH=0x00, DEV=0x00, STS=0x00
SMART Status not supported: Invalid ATA output register values
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test
routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 592) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 115) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x50bd) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 080 063 044 Pre-fail
Always - 116858893
3 Spin_Up_Time 0x0003 098 098 000 Pre-fail
Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age
Always - 6
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000f 070 060 030 Pre-fail
Always - 12572406
9 Power_On_Hours 0x0032 100 100 000 Old_age
Always - 626
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age
Always - 6
184 End-to-End_Error 0x0032 100 100 099 Old_age
Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age
Always - 0
188 Command_Timeout 0x0032 100 100 000 Old_age
Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age
Always - 0
190 Airflow_Temperature_Cel 0x0022 074 071 045 Old_age
Always - 26 (Min/Max 20/28)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age
Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age
Always - 5
193 Load_Cycle_Count 0x0032 100 100 000 Old_age
Always - 31
194 Temperature_Celsius 0x0022 026 040 000 Old_age
Always - 26 (0 20 0 0 0)
195 Hardware_ECC_Recovered 0x001a 050 011 000 Old_age
Always - 116858893
197 Current_Pending_Sector 0x0012 100 100 000 Old_age
Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age
Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
_______________________________________________
pld-users-pl mailing list
[email protected]
http://lists.pld-linux.org/mailman/listinfo/pld-users-pl
