I will have to give that a try. I am about fed up with WU, the acurite does not send wind direction data (at least from the console) when there is no wind speed, WU then pushes you down as their stupid interface considers your station "broke" because it does not show wind direction when there is no wind.
Tonight I went to check it and I am not even shown, so not sure what is going on, I see the WX data being sent and I get no complaints back about no being able to send it or it not being received so not sure what is going on. I am also on CWOP (AV216) and can also be seen on APRS as KP4DJT. Both of them show good data though CWOP seems to get heartburn from my DP readings since it has turned really cold but I have got comments from others that they see the same thing and it is due to the deltas between my station and those near me which are 600 ft below in the Columbia River valley where it is warmer (we have 2 in of new snow here tonight, dogs were out having a great old time in it). The one thing I have noticed with the acurite wireless data link is that is appears to get deep fades, not sure what takes it out but it does. I am trying to get IPv6 going here so I will have some routable addresses, I am on Hughesnet so the IP4 addys are not routable, but the IPv6 are, just trying to figure out how they handle some weirdness, and am trying to get up to speed on IPv6 anyhow. I may setup a separate router for IPv6 so I can butcher things and not lose my main path. Hughesnet will hand out up to 6 addys from the satellite modem/router so I could have 6 routers hanging off of the thing and each one of them had a assignment. Their idea is that you use there box as your local router, but I have WAY more than 5 devices here on line at this time. On Fri, Dec 30, 2016 at 9:38 AM, James Bertelson <[email protected]> wrote: > On 12/30/2016 08:32 AM, Chuck Hast wrote: > > That is interesting, I have two of them, one I use for demo's and to > setup > > for > > data captures in places where I might want a bit of data on a location, > and > > the > > other is just here at the house. The demo one lost the console the other > > day, > > and I am trying to figure out what did it perhaps it was too much 440 > Mhz RF > > from my Icom radio... I will have to check that out. > > > > So are you using the sensor head and just decoding the packets as they > are > > sent? If so that is interesting because I am going to get the bad console > > re- > > placed but I have been thinking about trying to decode the data direct > from > > the sensor head as I have a location I want to set one up but it is > remote > > and > > there is really not much need for the console if there is a way to > capture > > the > > data off of the sensor head and use it that way. > > > > Are you still using the RTL_433 as the radio? > > Exactly - the sensor is outside, and I have an rpi with a nooelec SDR > sitting in the house. The only thing you get from the console that the > station doesn't have is baro pressure. For that I picked up an i2c > sensor that's hooked up to the pi and read by the python script. > > I tossed it up here, if you want to give it a go. It's worked on both > an original model B and a pi 3 for me. > > https://github.com/diffra/AcuRiteSDR > -- > James Bertelson > [email protected] > :wq > _______________________________________________ > PLUG mailing list > [email protected] > http://lists.pdxlinux.org/mailman/listinfo/plug > -- Chuck Hast -- KP4DJT -- Glass, five thousand years of history and getting better. The only container material that the USDA gives blanket approval on. _______________________________________________ PLUG mailing list [email protected] http://lists.pdxlinux.org/mailman/listinfo/plug
