>----Messaggio originale---- >Da: [email protected] >Data: 26/06/2014 12.08 >A: <[email protected]> >Ogg: R: Re: Can't enable multicast > > > >>----Messaggio originale---- >>Da: [email protected] >>Data: 26/06/2014 1.28 >>A: "[email protected]"<[email protected]> >>Ogg: Re: Can't enable multicast >> >>On 06/25/14 23:46, [email protected] wrote: >></snipped> >>> >>> do you have any suggestions ?? thanks and sorry for my english >>> >> >>Also the output of netstat and route >> >>This is probably better on [email protected] - rather than ports@ >> >>hth >> >>Fred >> > >Hi Fred and thanks for your reply. Sorry for the delay but I live in Italy >and, at the time of your reply, I was sleeping :) > >btw my ifconfig em output is: >em0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 > lladdr 08:00:27:d9:6b:2f > priority: 0 > groups: egress > media: Ethernet autoselect (1000baseT full-duplex) > status: active > inet6 fe80::a00:27ff:fed9:6b2f%em0 prefixlen 64 scopeid 0x1 > inet 10.0.2.15 netmask 0xffffff00 broadcast 10.0.2.255 >em1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500 > lladdr 08:00:27:47:66:43 > priority: 0 > media: Ethernet autoselect (none) > status: no carrier >em2: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500 > lladdr 08:00:27:bc:6b:07 > priority: 0 > media: Ethernet autoselect (1000baseT full-duplex) > status: active > inet6 fe80::a00:27ff:febc:6b07%em2 prefixlen 64 scopeid 0x3 > inet 173.0.0.2 netmask 0xfffffffc broadcast 173.0.0.3 >em3: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500 > lladdr 08:00:27:bf:89:b8 > priority: 0 > media: Ethernet autoselect (none) > status: no carrier > >my netstat output is: >Active UNIX domain sockets >Address Type Recv-Q Send-Q Inode Conn Refs Nextref >Addr >0xd5d0d7cc stream 0 0 0x0 0xd170e580 0x0 0x0 >0xd5d0d6b0 stream 0 0 0xd5d15d28 0x0 0x0 0x0 >/var/quagga/ripd.vty >0xd5d0d240 dgram 0 0 0x0 0xd1871000 0x0 0xd1899580 >0xd5d0d8e8 stream 0 0 0x0 0xd1899400 0x0 0x0 >/var/quagga/zserv.api >0xd5d0d124 stream 0 0 0xd5d158e4 0x0 0x0 0x0 >/var/quagga/zebra.vty >0xd5d46d54 stream 0 0 0xd5d157ac 0x0 0x0 0x0 >/var/quagga/zserv.api >0xd5d46a00 dgram 0 0 0x0 0xd1871000 0x0 0xd1871c80 >0xd5d468e4 stream 0 0 0xd5d2fb4c 0x0 0x0 0x0 >tabs/.sock >0xd5d467c8 dgram 0 0 0x0 0xd1871000 0x0 0xd1871880 >0xd5d466ac stream 0 0 0xd5d2f3fc 0x0 0x0 0x0 >/tmp/aucat/aucat0 >0xd5d4623c dgram 0 0 0x0 0xd1871000 0x0 0xd1871a00 >0xd5e55d50 dgram 0 0 0x0 0xd1871000 0x0 0x0 >0xd5e55c34 stream 0 0 0x0 0xd1871800 0x0 0x0 >0xd5e55b18 stream 0 0 0x0 0xd1871700 0x0 0x0 >0xd5e559fc stream 0 0 0x0 0xd1871380 0x0 0x0 >0xd5e558e0 stream 0 0 0x0 0xd1871400 0x0 0x0 >0xd5e557c4 dgram 0 0 0xd5e026d8 0x0 0x0 0x0 >/var/empty/dev/log >0xd5e556a8 dgram 0 0 0xd5e0263c 0x0 0x0 0x0 >/var/www/dev/log >0xd5e5558c dgram 0 0 0xd5e025a0 0x0 0xd1899080 0x0 >/dev/log >0xd5e55238 stream 0 0 0x0 0xd1756c00 0x0 0x0 >0xd5e5511c stream 0 0 0x0 0xd1756d80 0x0 0x0 > >the route command needs more arguments > >I hope it helps :) >
