Hello ports@:
I'm having a problem getting saned to work. The scanner, through either
the simple-scan or xsane front-ends, errors-out with the message "Error
communicating with scanner".
My machine is an x86_64 running -current; my scanner is an all-in-one
Canon Pixma MG2520. sane does support this device. dmesg and output of
<usbdevs -vd> is below.
After the saned package installation, I reviewed the information at
/usr/local/share/doc/pkg-readmes/sane-backends-1.0.25p3 and made the
group and ownership changes and I am a member of the _saned group:
-----
/dev $ doas usbdevs -vd
Controller /dev/usb0:
addr 1: high speed, self powered, config 1, EHCI root hub(0x0000),
Intel(0x8086), rev 1.00
uhub0
port 1 powered
port 2 powered
port 3 powered
port 4 addr 2: high speed, self powered, config 1, MG2500
series(0x176d),
Canon(0x04a9), rev 1.10, iSerialNumber 3DE842
ulpt0
ugen0
port 5 powered
port 6 powered
-----
/dev $ ls -l | grep -i _saned
crw-rw---- 1 _cups _saned 63, 0 May 7 07:59 ugen0.00
crw-rw---- 1 _cups _saned 63, 1 May 7 07:59 ugen0.01
crw-rw---- 1 _cups _saned 63, 2 May 7 07:59 ugen0.02
crw-rw---- 1 _cups _saned 63, 3 May 7 07:59 ugen0.03
crw-rw---- 1 _cups _saned 63, 4 May 7 07:59 ugen0.04
crw-rw---- 1 _cups _saned 63, 5 May 7 07:59 ugen0.05
crw-rw---- 1 _cups _saned 63, 6 May 7 07:59 ugen0.06
crw-rw---- 1 _cups _saned 63, 7 May 9 11:57 ugen0.07
crw-rw---- 1 _cups _saned 63, 8 May 7 07:59 ugen0.08
crw-rw---- 1 _cups _saned 63, 9 May 7 07:59 ugen0.09
crw-rw---- 1 _cups _saned 63, 10 May 7 07:59 ugen0.10
crw-rw---- 1 _cups _saned 63, 11 May 7 07:59 ugen0.11
crw-rw---- 1 _cups _saned 63, 12 May 7 07:59 ugen0.12
crw-rw---- 1 _cups _saned 63, 13 May 7 07:59 ugen0.13
crw-rw---- 1 _cups _saned 63, 14 May 7 07:59 ugen0.14
crw-rw---- 1 _cups _saned 63, 15 May 7 07:59 ugen0.15
crw-rw---- 1 _cups _saned 64, 0 May 7 07:59 ulpt0
crw-rw---- 1 root _saned 61, 0 May 7 07:59 usb0
crw-rw---- 1 _cups _saned 61, 1 May 7 07:59 usb1
-----
/home/dutch $ id
uid=1000(dutch) gid=1000(dutch) groups=1000(dutch), 0(wheel),
735(_wireshark), 541(_cups), 553(_saned)
-----
I then checked whether saned was running with rcctl:
-----
/home/dutch $ doas rcctl ls on
check_quotas
cron
ntpd
pf
pflogd
saned
smtpd
sndiod
syslogd
-----
/home/dutch $ doas rcctl ls started
cron
cupsd
ntpd
pflogd
saned
smtpd
sndiod
syslogd
(To get saned started, I had to run </usr/local/libexec/saned -a dutch>;
prior to that saned was "on" but not "started"). I also added a routine
to /etc/rc.local to start saned at boot.
-----
I'm out of ideas. If anyone can point out what I'm missing, I'd be
grateful. Thanks.
dmesg:
/home/dutch $ dmesg
OpenBSD 5.9-current (GENERIC.MP) #2007: Fri May 6 12:51:40 MDT 2016
[email protected]:/usr/src/sys/arch/amd64/compile/GENERIC.MP
RTC BIOS diagnostic error 11<memory_size>
real mem = 8436838400 (8045MB)
avail mem = 8176545792 (7797MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.5 @ 0xf0450 (82 entries)
bios0: vendor Dell Inc. version "A03" date 02/13/2010
bios0: Dell Inc. OptiPlex 780
acpi0 at bios0: rev 2
acpi0: TCPA checksum error
acpi0: sleep states S0 S1 S3 S4 S5
acpi0: tables DSDT FACP SSDT APIC BOOT ASF! MCFG HPET TCPA ____ SLIC
acpi0: wakeup devices VBTN(S4) PCI0(S5) PCI4(S5) PCI3(S5) PCI1(S5)
PCI5(S5) PCI6(S5) MOU_(S3) USB0(S3) USB1(S3) USB2(S3) USB3(S3) USB4(S3)
USB5(S3)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz, 2992.91 MHz
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,XSAVE,NXE,LONG,LAHF,PERF,SENSOR
cpu0: 6MB 64b/line 16-way L2 cache
cpu0: smt 0, core 0, package 0
mtrr: Pentium Pro MTRR support, 7 var ranges, 88 fixed ranges
cpu0: apic clock running at 332MHz
cpu0: mwait min=64, max=64, C-substates=0.2.2.2.2, IBE
cpu1 at mainbus0: apid 1 (application processor)
cpu1: Intel(R) Core(TM)2 Duo CPU E8400 @ 3.00GHz, 2992.50 MHz
cpu1:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,SSE4.1,XSAVE,NXE,LONG,LAHF,PERF,SENSOR
cpu1: 6MB 64b/line 16-way L2 cache
cpu1: smt 0, core 1, package 0
ioapic0 at mainbus0: apid 8 pa 0xfec00000, version 20, 24 pins
ioapic0: misconfigured as apic 0, remapped to apid 8
acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255
acpihpet0 at acpi0: 14318179 Hz
acpiprt0 at acpi0: bus 4 (PCI4)
acpiprt1 at acpi0: bus 2 (PCI2)
acpiprt2 at acpi0: bus 3 (PCI3)
acpiprt3 at acpi0: bus 1 (PCI1)
acpiprt4 at acpi0: bus -1 (PCI5)
acpiprt5 at acpi0: bus -1 (PCI6)
acpiprt6 at acpi0: bus 0 (PCI0)
acpicpu0 at acpi0: C1(1000@1 mwait.1)
acpicpu1 at acpi0: C1(1000@1 mwait.1)
acpibtn0 at acpi0: VBTN
"*pnp0c14" at acpi0 not configured
"PNP0401" at acpi0 not configured
"PNP0501" at acpi0 not configured
"PNP0501" at acpi0 not configured
cpu0: unknown Enhanced SpeedStep CPU, msr 0x0616092606000926
cpu0: using only highest and lowest power states
cpu0: Enhanced SpeedStep 2992 MHz: speeds: 3000, 2000 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel Q45 Host" rev 0x03
ppb0 at pci0 dev 1 function 0 "Intel Q45 PCIE" rev 0x03: msi
pci1 at ppb0 bus 1
radeondrm0 at pci1 dev 0 function 0 "ATI Radeon HD 5450" rev 0x00
drm0 at radeondrm0
radeondrm0: msi
azalia0 at pci1 dev 0 function 1 "ATI Radeon HD 5470 Audio" rev 0x00:
msi
azalia0: no supported codecs
"Intel Q45 HECI" rev 0x03 at pci0 dev 3 function 0 not configured
pciide0 at pci0 dev 3 function 2 "Intel Q45 PT IDER" rev 0x03: DMA
(unsupported), channel 0 wired to native-PCI, channel 1 wired to
native-PCI
pciide0: using apic 8 int 18 for native-PCI interrupt
pciide0: channel 0 ignored (not responding; disabled or no drives?)
pciide0: channel 1 ignored (not responding; disabled or no drives?)
puc0 at pci0 dev 3 function 3 "Intel Q45 KT" rev 0x03: ports: 1 com
com4 at puc0 port 0 apic 8 int 17: ns16550a, 16 byte fifo
com4: probed fifo depth: 15 bytes
em0 at pci0 dev 25 function 0 "Intel ICH10 D BM LM" rev 0x02: msi,
address b8:ac:6f:a4:35:01
uhci0 at pci0 dev 26 function 0 "Intel 82801JD USB" rev 0x02: apic 8 int
16
uhci1 at pci0 dev 26 function 1 "Intel 82801JD USB" rev 0x02: apic 8 int
17
uhci2 at pci0 dev 26 function 2 "Intel 82801JD USB" rev 0x02: apic 8 int
22
ehci0 at pci0 dev 26 function 7 "Intel 82801JD USB" rev 0x02: apic 8 int
22
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
azalia1 at pci0 dev 27 function 0 "Intel 82801JD HD Audio" rev 0x02: msi
azalia1: codecs: Analog Devices AD1984A
audio0 at azalia1
ppb1 at pci0 dev 28 function 0 "Intel 82801JD PCIE" rev 0x02: msi
pci2 at ppb1 bus 2
ppb2 at pci0 dev 28 function 1 "Intel 82801JD PCIE" rev 0x02: msi
pci3 at ppb2 bus 3
uhci3 at pci0 dev 29 function 0 "Intel 82801JD USB" rev 0x02: apic 8 int
23
uhci4 at pci0 dev 29 function 1 "Intel 82801JD USB" rev 0x02: apic 8 int
17
uhci5 at pci0 dev 29 function 2 "Intel 82801JD USB" rev 0x02: apic 8 int
18
ehci1 at pci0 dev 29 function 7 "Intel 82801JD USB" rev 0x02: apic 8 int
23
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb3 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0xa2
pci4 at ppb3 bus 4
pcib0 at pci0 dev 31 function 0 "Intel 82801JDO LPC" rev 0x02
ahci0 at pci0 dev 31 function 2 "Intel 82801JD AHCI" rev 0x02: msi, AHCI
1.2
ahci0: port 0: 3.0Gb/s
ahci0: port 1: 1.5Gb/s
ahci0: PHY offline on port 2
scsibus1 at ahci0: 32 targets
sd0 at scsibus1 targ 0 lun 0: <ATA, SAMSUNG HD083GJ, 1AC0> SCSI3
0/direct fixed naa.50000f000b017238
sd0: 76293MB, 512 bytes/sector, 156250000 sectors
cd0 at scsibus1 targ 1 lun 0: <PLDS, DVD+-RW DS-8A4S, JD12> ATAPI
5/cdrom removable
ichiic0 at pci0 dev 31 function 3 "Intel 82801JD SMBus" rev 0x02: apic 8
int 18
iic0 at ichiic0
spdmem0 at iic0 addr 0x50: 4GB DDR3 SDRAM PC3-10600
spdmem1 at iic0 addr 0x52: 4GB DDR3 SDRAM PC3-10600
usb2 at uhci0: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci1: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci2: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb5 at uhci3: USB revision 1.0
uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb6 at uhci4: USB revision 1.0
uhub6 at usb6 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb7 at uhci5: USB revision 1.0
uhub7 at usb7 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5 irq 1 irq 12
pckbd0 at pckbc0 (kbd slot)
wskbd0 at pckbd0: console keyboard
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
ulpt0 at uhub0 port 4 configuration 1 interface 1 "Canon MG2500 series"
rev 2.00/1.10 addr 2
ulpt0: using bi-directional mode
ugen0 at uhub0 port 4 configuration 1 "Canon MG2500 series" rev
2.00/1.10 addr 2
uhidev0 at uhub3 port 1 configuration 1 interface 0 "Razer Razer
BlackWidow Refresh Tournament Edition" rev 2.00/2.00 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 variable keys, 6 key codes
wskbd1 at ukbd0 mux 1
uhidev1 at uhub3 port 1 configuration 1 interface 1 "Razer Razer
BlackWidow Refresh Tournament Edition" rev 2.00/2.00 addr 2
uhidev1: iclass 3/0, 5 report ids
ukbd1 at uhidev1 reportid 1: 8 variable keys, 6 key codes
wskbd2 at ukbd1 mux 1
uhid0 at uhidev1 reportid 2: input=15, output=0, feature=0
uhid1 at uhidev1 reportid 3: input=15, output=0, feature=0
uhid2 at uhidev1 reportid 4: input=15, output=0, feature=0
uhid3 at uhidev1 reportid 5: input=15, output=0, feature=0
uhidev2 at uhub3 port 1 configuration 1 interface 2 "Razer Razer
BlackWidow Refresh Tournament Edition" rev 2.00/2.00 addr 2
uhidev2: iclass 3/0
ums0 at uhidev2: 3 buttons, Z dir
wsmouse0 at ums0 mux 0
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
scsibus3 at softraid0: 256 targets
root on sd0a (8311448ffa412adf.a) swap on sd0b dump on sd0b
radeondrm0: 1440x900
wsdisplay0 at radeondrm0 mux 1: console (std, vt100 emulation), using
wskbd0
wskbd1: connecting to wsdisplay0
wskbd2: connecting to wsdisplay0
wsdisplay0: screen 1-5 added (std, vt100 emulation)
uhidev3 at uhub5 port 1 configuration 1 interface 0 "Logitech USB
Receiver" rev 2.00/22.01 addr 2
uhidev3: iclass 3/1
ums1 at uhidev3: 16 buttons, Z and W dir
wsmouse1 at ums1 mux 0
uhidev4 at uhub5 port 1 configuration 1 interface 1 "Logitech USB
Receiver" rev 2.00/22.01 addr 2
uhidev4: iclass 3/0, 17 report ids
uhid4 at uhidev4 reportid 3: input=4, output=0, feature=0
uhid5 at uhidev4 reportid 16: input=6, output=6, feature=0
uhid6 at uhidev4 reportid 17: input=19, output=19, feature=0
/home/dutch $
-----
