> @Simon: Yes used the manpage example initially but then I found that i > need > to map various different location servers on a single Public IP. Thus I > have > a rather long pound.cfg file. I am attaching the complete file for your > reference > > Attaching error details > > On the browser I get the error > "The service is not available. Please try again later." > > while in the syslog I get this error > pound : no back-end "GET /sr2notesheet/ HTTP/1.0"
I hope that's a type ^^^^^^^ Because you refer to "^/sr2enotesheet" in your config. Simon > > Although I can browse the backend fine from the pound server web browser. > > I believe pound is getting confused between sr2 and sr2enotesheet. > > Regards > > Dhiraj gaur > > On Mon, Nov 16, 2009 at 1:38 PM, Dhiraj Gaur <[email protected]> > wrote: > >> HI >> I intially started off with a URL "^/sr2enotesheet" but then the tweaks >> led >> me to the current thing URL "^/sr2enotesheet\/*". >> Both give me the same error. :( >> >> Regards >> Dhiraj Gaur >> >> On Mon, Nov 16, 2009 at 1:26 PM, Simon Matter <[email protected] >> >wrote: >> >> > > Hi all >> > > >> > > I have been using Pound in my setup for quite sometime now. I have >> setup >> > > various backends so that on the basis of URL request I can fetch >> pages >> > > from >> > > various backend servers. For eg http://publicip/sr1 shall fetch page >> > from >> > > Location 1 while http://publicip/sr2 shall fetch pages from location >> 2 >> > > >> > >> > Hi, >> > >> > I was just wondering about your URL directive and the one I'm using on >> my >> > own sites. Maybe I just didn't care enough but for the line you have >> > >> > URL "^/sr2enotesheet\/*" >> > >> > mine would look like >> > >> > URL "/sr2enotesheet/.*" >> > >> > Now I wondering why I'm not escaping / and why I'm not marking >> beginning >> > of the line with ^? >> > >> > Did you try the version used in the manpage, which mine is based on? >> > >> > Regards, >> > Simon >> > >> > >> > > Thus being on a single HTTP listener I can fetch pages from various >> > > locations simply on the basis of URL. >> > > >> > > PROBLEM : >> > > Now I have a request from one of my locations to add one more >> backend. >> > The >> > > problem is the URL pattern. SR2 as a backend is already defined and >> > > working. >> > > When I add another backend with URL setting sr2email, POUND does not >> seem >> > > to >> > > recognize the backend (even after service restart). and I see that >> > > requests >> > > somehow are queried on sr2 backend. >> > > >> > > The issue seems to go away when I rename sr2email to something other >> than >> > > which starts with sr2(say xyz) >> > > >> > > Plz help me where am I going wrong ??? >> > > >> > > Pound.cfg: >> > > >> > > Service "sr1" >> > > URL "^/sr1" >> > > BackEnd >> > > Address 192.168.14.26 >> > > Port 80 >> > > End >> > > End >> > > >> > > Service "sr2enotesheet" >> > > URL "^/sr2enotesheet\/*" >> > > BackEnd >> > > Address 192.168.13.24 >> > > Port 9009 >> > > End >> > > End >> > > >> > > Service "sr2" >> > > URL "^/sr2\/*" >> > > BackEnd >> > > Address 192.168.13.25 >> > > Port 8008 >> > > End >> > > End >> > > >> > > >> > > Regards >> > > >> > > Dhiraj Gaur >> > > >> > > >> > > -- >> > > To unsubscribe send an email with subject unsubscribe to >> [email protected]. >> > > Please contact [email protected] for questions. >> > > >> > >> > >> > >> > -- >> > To unsubscribe send an email with subject unsubscribe to >> [email protected]. >> > Please contact [email protected] for questions. >> > >> >> >> -- >> To unsubscribe send an email with subject unsubscribe to [email protected]. >> Please contact [email protected] for questions. >> > > > -- > To unsubscribe send an email with subject unsubscribe to [email protected]. > Please contact [email protected] for questions. > -- To unsubscribe send an email with subject unsubscribe to [email protected]. Please contact [email protected] for questions.
