Thanks joe ill check it out Sent from my iPhone4 on IOS4
On Jan 7, 2011, at 5:06 PM, Joe Gooch <[email protected]> wrote: > The pound project does not package a binary at all. Any packaging support > would be done by external maintainers. I merely provided the Debian > information because I run Debian and could run apt-cache policy. > > A 10sec google search yields that 2.4.5 is available in lucid. > http://packages.ubuntu.com/lucid/pound > > There's apparently further ubuntu documentation here: > https://help.ubuntu.com/community/Pound > > Which I believe just about covers what you're asking... Since the example has > multiple backends and illustrates the HeadRequire directive. > > Joe > >> -----Original Message----- >> From: Nelson Pereira [mailto:[email protected]] >> Sent: Friday, January 07, 2011 4:50 PM >> To: [email protected] >> Subject: Re: [Pound Mailing List] Question on setup >> >> So no lucid support? >> >> Sent from my iPhone4 on IOS4 >> >> On Jan 7, 2011, at 4:47 PM, Joe Gooch <[email protected]> wrote: >> >>> 2.4.3 is available in Lenny, 2.5 is available in squeeze and sid. >>> >>> Joe >>> >>>> -----Original Message----- >>>> From: Nelson Pereira [mailto:[email protected]] >>>> Sent: Friday, January 07, 2011 4:34 PM >>>> To: [email protected] >>>> Subject: Re: [Pound Mailing List] Question on setup >>>> >>>> Ok, but how do you configure it and how is it called? I can install >> it >>>> on a ubuntu 10.10 server, any special package requirement? Is there >> a >>>> debian packe available for pound? >>>> >>>> Sent from my iPhone4 on IOS4 >>>> >>>> On Jan 7, 2011, at 4:17 PM, Dave Steinberg <[email protected]> >> wrote: >>>> >>>>> On 1/7/2011 4:00 PM, Nelson Pereira wrote: >>>>>> Not sure if pound can do this but here is what i need to do: >>>>>> web1.mydomain.com resolves to 209.5.5.5 which is my public IP on >> the >>>>>> external side of my router. Router is setup to forward (port >>>> forwarding) all >>>>>> port 80 based traffic to internal ip 192.168.1.10 (my PVE system) >>>> which I >>>>>> want that server to lookup the request, and for web1 forward to >>>>>> 192.168.1.101, for web2 to .102 etc.... Can pound do this and if >> so, >>>> how >>>>>> should it be configured and what is the configuration file? >>>>>> Is there a web GUI to configure pound? >>>>> >>>>> Yes, you want to use the 'HeadRequire' directive. You should >> follow >>>> the example on apsis.ch/pound under the section "VIRTUAL HOSTS (IN >>>> GENERAL)". I believe that describes what you want. >>>>> >>>>> You get to choose your favorite text editor as the gui for >>>> configuring pound. :) >>>>> >>>>> Regards, >>>>> -- >>>>> Dave Steinberg >>>>> http://www.geekisp.com/ >>>>> http://www.steinbergcomputing.com/ >>>>> http://www.redterror.net/ >>>>> >>>>> -- >>>>> To unsubscribe send an email with subject unsubscribe to >>>> [email protected]. >>>>> Please contact [email protected] for questions. >>>> >>>> -- >>>> To unsubscribe send an email with subject unsubscribe to >>>> [email protected]. >>>> Please contact [email protected] for questions. >>> >>> -- >>> To unsubscribe send an email with subject unsubscribe to >> [email protected]. >>> Please contact [email protected] for questions. >> >> -- >> To unsubscribe send an email with subject unsubscribe to >> [email protected]. >> Please contact [email protected] for questions. > > -- > To unsubscribe send an email with subject unsubscribe to [email protected]. > Please contact [email protected] for questions. -- To unsubscribe send an email with subject unsubscribe to [email protected]. Please contact [email protected] for questions.
