It appears ubuntu maverick has a pound 2.5 package. http://packages.ubuntu.com/source/maverick/pound
Joe > -----Original Message----- > From: Joe Gooch [mailto:[email protected]] > Sent: Monday, January 10, 2011 12:05 PM > To: [email protected] > Subject: RE: [Pound Mailing List] About https > > You would need to pull a pound 2.5 deb package (for instance from > debian sid), or compile pound yourself. (Or at least compile pound and > replace the pound binary in /usr/sbin or wherever the package put it) > > See http://www.apsis.ch/pound/index_html, installation section. > > Joe > > > > -----Original Message----- > > From: Nelson Pereira [mailto:[email protected]] > > Sent: Monday, January 10, 2011 11:18 AM > > To: [email protected] > > Subject: Re: [Pound Mailing List] About https > > > > My version is : > > > > r...@pound:~# pound -V > > starting... > > Version 2.4.5 > > Configuration switches: > > --enable-cert1l > > > > > > i installed using apt-get, how do I upgrade to 2.5c as apt-get does > not > > have > > that release? > > > > NP > > > > On Mon, Jan 10, 2011 at 11:03 AM, Joe Gooch <[email protected]> > > wrote: > > > > > Support for HTTPS backends was added in Pound 2.5c. > > > > > > You configure in a backend group by using the HTTPS Directive. > From > > the > > > Pound manual page: > > > > > > BackEnd > > > A back-end is a definition of a single back-end server Pound > > will use > > > to reply to incoming requests. All configuration directives > enclosed > > > between BackEnd and End > > > are specific to a single service. The following directives > are > > > available: > > > > > > Address address > > > The address that Pound will connect to. This can be a > > numeric > > > IP address, or a symbolic host name that must be resolvable at run- > > time. If > > > the name cannot be > > > resolved to a valid address, Pound will assume that it > > > represents the path for a Unix-domain socket. This is a mandatory > > parameter. > > > > > > Port port > > > The port number that Pound will connect to. This is a > > > mandatory parameter for non Unix-domain back-ends. > > > > > > HTTPS [ "cert" ] > > > The back-end is using HTTPS. If the optional parameter > > cert is > > > specified, Pound will present this certificate to the back-end. > > > > > > Priority val > > > The priority of this back-end (between 1 and 9, 5 > is > > > default). Higher priority back-ends will be used more often than > > lower > > > priority ones, so you should > > > define higher priorities for more capable servers. > > > > > > TimeOut val > > > Override the global TimeOut value. > > > > > > ConnTO val > > > Override the global ConnTO value. > > > > > > HAport [ address ] port > > > A port (and optional address) to be used for server > > function > > > checks. See below the "High Availability" section for a more > detailed > > > discussion. By default > > > Pound uses the same address as the back-end server, > but > > you > > > may use a separate address if you wish. This directive applies only > > to non > > > Unix-domain servers. > > > > > > > > > Joe > > > > > > > > > > -----Original Message----- > > > > From: nelson pereira [mailto:[email protected]] > > > > Sent: Sunday, January 09, 2011 9:51 PM > > > > To: [email protected] > > > > Subject: Re: [Pound Mailing List] About https > > > > > > > > does pound do https to https backend? > > > > > > > > I think this is something proxmox does not actualy do.. am i > wrong? > > > > > > > > Nelson > > > > > > > > On Jan 9, 2011, at 5:33 PM, Dave Steinberg wrote: > > > > > > > > > On 1/9/2011 5:25 PM, Nelson Pereira wrote: > > > > >> done that, and the service looks like this: > > > > >> > > > > >> Service > > > > >> HeadRequire "Host:.*proxmox.mydomain.com.*" > > > > >> BackEnd > > > > >> Address 192.168.1.10 > > > > >> Port 443 > > > > >> End > > > > >> End > > > > >> > > > > >> Yet I keep getting the logs in syslog: > > > > >> can't read header > > > > >> e500 response error read from 192.168.1.10:443/GET / HTTP/1.1: > > > > Success > > > > >> (0.001 secs) > > > > >> > > > > >> and then i get a page cannot be displayed. > > > > > > > > > > Try adding "HTTPS" to the backend directive. I'm not 100% sure > > of > > > > the syntax there, I think its literally a bareword as in: > > > > > > > > > > BackEnd > > > > > Address 192... > > > > > Port 443 > > > > > HTTPS > > > > > End > > > > > > > > > > That will tell pound to talk https to the backend. I don't use > > that > > > > myself so I can't advise precisely how it should look, but play > > around > > > > with it or maybe check the archives to see if there are examples. > > > > > > > > > > Regards, > > > > > -- > > > > > Dave Steinberg > > > > > http://www.geekisp.com/ > > > > > http://www.steinbergcomputing.com/ > > > > > http://www.redterror.net/ > > > > > > > > > > -- > > > > > To unsubscribe send an email with subject unsubscribe to > > > > [email protected]. > > > > > Please contact [email protected] for questions. > > > > > > > > > > > > -- > > > > To unsubscribe send an email with subject unsubscribe to > > > > [email protected]. > > > > Please contact [email protected] for questions. > > > > > > -- > > > To unsubscribe send an email with subject unsubscribe to > > [email protected]. > > > Please contact [email protected] for questions. > > > > > > > > > -- > > To unsubscribe send an email with subject unsubscribe to > > [email protected]. > > Please contact [email protected] for questions. > > -- > To unsubscribe send an email with subject unsubscribe to > [email protected]. > Please contact [email protected] for questions. -- To unsubscribe send an email with subject unsubscribe to [email protected]. Please contact [email protected] for questions.
