Hello,
You told "I can't ping to controller either". Did you check
connectivity between both hosts?
2014-08-29 13:32 GMT-03:00 Chanthan Hel <hel.chantha...@gmail.com>:
> Thanks Murphy ,
> I will try it
>
> On Friday, August 29, 2014, Murphy McCauley <murphy.mccau...@gmail.com>
> wrote:
>
>> Remove eth3 from the OVS datapath and make sure it still has the IP you
>> think it should.
>>
>> Please consider not dropping this list.
>>
>> -- Murphy
>>
>> On Aug 29, 2014, at 12:16 AM, Chanthan Hel <hel.chantha...@gmail.com>
>> wrote:
>>
>> Hi Murphy
>> Eth3 that connects to controller has ip 172.16.0.1 in the same netmask
>> with controller.
>> That port is USB port, but I use USB to ethernet adapter. And about what
>> u said, in bound control! I'm not so clear . How can we assign it to in
>> bound or out bound controll.
>> Best regards
>>
>>
>> On Friday, August 29, 2014, Murphy McCauley <murphy.mccau...@gmail.com>
>> wrote:
>>
>>> It's strange that just installing OVS would cause a problem unless you
>>> assigned the port that leads to the controller to the switch without
>>> setting up in-band control.
>>>
>>> Is eth1 connected to the controller? Does it have a 172.16.x.x address
>>> or whatever?
>>>
>>> -- Murphy
>>>
>>> On Aug 28, 2014, at 1:32 AM, Chanthan Hel <hel.chantha...@gmail.com>
>>> wrote:
>>>
>>> Dear all,
>>> Please help me for this point.
>>> I install open vswitch in one PC and pox controller in another PC and i
>>> use Ethernet cable to connect. IP of controller and ovs are in same subnet
>>> mask.
>>>
>>> i install open vswitch as mentioned in installation guide
>>>
>>> http://git.openvswitch.org/cgi-bin/gitweb.cgi?p=openvswitch;a=blob_plain;f=INSTALL;hb=HEAD
>>>
>>> i added port to switch as shown
>>> root@pc2-To-be-filled-by-O-E-M:~/openvswitch-1.9.0# ovs-ofctl show s2
>>> OFPT_FEATURES_REPLY (xid=0x1): dpid:0000000000002201
>>> n_tables:255, n_buffers:256
>>> capabilities: FLOW_STATS TABLE_STATS PORT_STATS QUEUE_STATS ARP_MATCH_IP
>>> actions: OUTPUT SET_VLAN_VID SET_VLAN_PCP STRIP_VLAN SET_DL_SRC
>>> SET_DL_DST SET_NW_SRC SET_NW_DST SET_NW_TOS SET_TP_SRC SET_TP_DST ENQUEUE
>>> 1(eth2): addr:00:00:00:00:22:04
>>> config: 0
>>> state: LINK_DOWN
>>> current: 100MB-FD AUTO_NEG
>>> advertised: 10MB-HD 10MB-FD 100MB-HD 100MB-FD COPPER AUTO_NEG
>>> AUTO_PAUSE AUTO_PAUSE_ASYM
>>> supported: 10MB-HD 10MB-FD 100MB-HD 100MB-FD COPPER AUTO_NEG
>>> speed: 100 Mbps now, 100 Mbps max
>>> 2(eth3): addr:00:00:00:00:22:05
>>> config: 0
>>> state: 0
>>> current: 100MB-FD AUTO_NEG
>>> advertised: 10MB-HD 10MB-FD 100MB-HD 100MB-FD COPPER AUTO_NEG
>>> AUTO_PAUSE AUTO_PAUSE_ASYM
>>> supported: 10MB-HD 10MB-FD 100MB-HD 100MB-FD COPPER AUTO_NEG
>>> speed: 100 Mbps now, 100 Mbps max
>>> 3(eth4): addr:00:00:00:00:22:01
>>> config: 0
>>> state: LINK_DOWN
>>> current: 100MB-FD AUTO_NEG
>>> advertised: 10MB-HD 10MB-FD 100MB-HD 100MB-FD COPPER AUTO_NEG
>>> AUTO_PAUSE AUTO_PAUSE_ASYM
>>> supported: 10MB-HD 10MB-FD 100MB-HD 100MB-FD COPPER AUTO_NEG
>>> speed: 100 Mbps now, 100 Mbps max
>>> LOCAL(s2): addr:00:00:00:00:22:01
>>> config: PORT_DOWN
>>> state: LINK_DOWN
>>> speed: 100 Mbps now, 100 Mbps max
>>> OFPT_GET_CONFIG_REPLY (xid=0x3): frags=normal miss_send_len=0
>>>
>>> but when i run pox, i check the ovs status it shows
>>>
>>> root@pc2-To-be-filled-by-O-E-M:~/openvswitch-1.9.0# ovs-vsctl show
>>> 849f606f-023d-435c-9548-1076994ec562
>>> Bridge "s2"
>>> Controller "tcp:172.16.0.9:6633"
>>> Port "s2"
>>> Interface "s2"
>>> type: internal
>>> Port "eth3"
>>> Interface "eth3"
>>> Port "eth2"
>>> Interface "eth2"
>>> Port "eth4"
>>> Interface "eth4"
>>> It means no connection to controller and I can't ping to controller
>>> either. But before installing ovs i can ping to controller. I don't know
>>> what happen.
>>> Best regards
>>> Chanthan
>>>
>>>
>>> --
>>> Mr. Chanthan Hel
>>> Electrical engineering, Faculty of Engineering,
>>> Chulalongkorn University (CU)
>>>
>>> *Phone: +66 81 456 84 27*
>>>
>>>
>>>
>>
>> --
>> Mr. Chanthan Hel
>> Electrical engineering, Faculty of Engineering,
>> Chulalongkorn University (CU)
>>
>> *Phone: +66 81 456 84 27*
>>
>>
>> <IMG_0924.JPG>
>>
>>
>>
>
> --
> Mr. Chanthan Hel
> Electrical engineering, Faculty of Engineering,
> Chulalongkorn University (CU)
>
> *Phone: +66 81 456 84 27*
>
>
>
