Also, if you run jconsole, a C&P executes each line as if they were entered serially.
On Fri, Aug 29, 2014 at 5:48 AM, Joe Bogner <[email protected]> wrote: > In addition to Linda's answer: > > for quick evaluation of scripts on the clipboard, you can use F8 in > jqt (Run->Clipboard). In JHS, there's a scratch window > (action->scratch) > > You can also do it manually from within jqt: > > NB. execute clipboard contents > (0!:1) wd 'clippaste' > > > > > > On Fri, Aug 29, 2014 at 5:17 AM, <[email protected]> wrote: > > Many thanks for your very helpful answer! :) > > > > ------ Originalnachricht ------ > > Von: "Linda Alvord" <[email protected]> > > An: [email protected] > > Gesendet: 29.08.2014 11:04:24 > > Betreff: Re: [Jprogramming] Copy & Paste > > > > > >> Sebastian, J has two environments and they are quite different, but they > >> are both also similar. Each has a an active "terminal". Cut and paste is > >> line by line as the terminal responds like a person. The dialog is > enter, > >> response, enter.. > >> > >> Each has a place for putting code. In jqt the choices are: open temp and > >> new temp. This is where you paste many lines of code. When you enter new > >> temp you are in a place to paste your long lines. It is different. You > are > >> in a place like a word processor for writing letters or email. You cut > and > >> paste happily. When it is correct, use run with all sorts of choices to > >> use > >> line by line or all at once. When you run, the response lands back in > the > >> terminal and you can continue until you need to edit again... Your code > is > >> now saved as a temp file called 1.ijs. When you like it you can save > as... > >> > >> However, in jhs things seem rather different at first. Once you have a > >> console working and j installed you are in a browser like chrome. You > >> start > >> with link: the two choices are ijix and ijis. Ijix is the same as term. > >> So this is where you have a dialog. ijis is for a script like temp > above. > >> If you now go to ijis you will get 2.ijs because you already have saved > >> 1.ijs. There are fewer choices now, but they should make sense. > >> > >> Interestingly you can now open 1.ijs and run it in your browser. You cut > >> and paste here in ijis and save and run. > >> > >> If you get something you want to share, I seem to have better luck when > I > >> cut a paste results from ijix when I want to put the results in an > email. > >> > >> Once you digest all this please let us know when you hit another > >> challenge. > >> > >> Linda > >> > >> -----Original Message----- > >> From: [email protected] > >> [mailto:[email protected]] On Behalf Of > >> [email protected] > >> Sent: Friday, August 29, 2014 4:14 AM > >> To: [email protected] > >> Subject: [Jprogramming] Copy & Paste > >> > >> Hi, > >> > >> How can I actually copy and paste J scripts to a term window and execute > >> the code directly. So far I copied small scripts (only a few lines) line > >> per line, but this is not a really solution and now I have to copy > >> scripts with many lines. > >> > >> Best regards, > >> Sebastian > >> ---------------------------------------------------------------------- > >> For information about J forums see http://www.jsoftware.com/forums.htm > >> > >> ---------------------------------------------------------------------- > >> For information about J forums see http://www.jsoftware.com/forums.htm > > > > > > ---------------------------------------------------------------------- > > For information about J forums see http://www.jsoftware.com/forums.htm > ---------------------------------------------------------------------- > For information about J forums see http://www.jsoftware.com/forums.htm > -- Devon McCormick, CFA ---------------------------------------------------------------------- For information about J forums see http://www.jsoftware.com/forums.htm
