I'm not so sure because I seldom use JQT or dissect. there seems an option in config to control qt ide to load dissect during booting up. you can check config and enable auto load.
On Wed, May 16, 2018, 2:39 AM Ulrich Vollert <[email protected]> wrote: > Hello Raul, > > that solved my problem - thank you very much. > > Thank you Pascal, too. > > A new programming environment is always challenging in the beginning - and > J is quite special compared to other languages. > > But I am very much motivated to invest some time in learning J: > > Regards, > Ulrich > > > > > Am 15.05.2018 um 20:04 schrieb 'Pascal Jasmin' via Programming < > [email protected]>: > > > > in previous versions (and likely current status), you needed to reload > jqt after any edit of the key shortcut settings file. > > > > > > > > ________________________________ > > From: Raul Miller <[email protected]> > > To: Programming forum <[email protected]> > > Sent: Tuesday, May 15, 2018 8:55 AM > > Subject: Re: [Jprogramming] Dissect in JQT > > > > > > > > That error message means that the dissect library was not loaded. > > > > You have several options including: > > > > (0) load it manually > > (1) have your profile load it > > (2) add [ require 'debug/dissect' to the end of each of those user > > keys config lines: > > > > F2;0;Dissect Line;dissect&.finddissectline_dissect_ 0 > [require'debug/dissect' > > F3;0;Dissect Last Error;dissect&.finddissectline_dissect_ 1 > > [require'debug/dissect' > > F4;0;Dissect Clipboard;dissect&.finddissectline_dissect_ 2 > > [require'debug/dissect' > > > > (beware email line wrap) > > > > Thanks, > > > > -- > > Raul > > > > On Tue, May 15, 2018 at 4:37 AM, Ulrich Vollert <[email protected]> wrote: > >> Hello, > >> > >> I am new to J and I am very impressed by J. > >> > >> Doing my first steps in learning J, I found ‚Dissect‘ and followed the > instructions in wiki/Vocabulary/Dissect#IDE to use it with PF keys: > >> > >> But after putting the following lines into Edit>Configure>User Keys in > Jqt > >> > >> F2;0;Dissect Line;dissect&.finddissectline_dissect_ 0 > >> F3;0;Dissect Last Error;dissect&.finddissectline_dissect_ 1 > >> F4;0;Dissect Clipboard;dissect&.finddissectline_dissect_ 2 > >> I get an error message when I try to use a PF key: > >> > >> |value error: finddissectline_dissect_ > >> | dissect&.finddissectline_dissect_ 1 > >> |[-0] > >> > >> I am using j806/j64/darwin with Library 8.06.09 and Qt IDE 1.6.2s/5.6.3 > on Darwin 64 (macOS 10.13.4) > >> > >> Thank you very much in advance for your help, > >> best regards > >> Ulrich > >> ---------------------------------------------------------------------- > >> For information about J forums see http://www.jsoftware.com/forums.htm > > > > ---------------------------------------------------------------------- > > For information about J forums see http://www.jsoftware.com/forums.htm > > ---------------------------------------------------------------------- > > For information about J forums see http://www.jsoftware.com/forums.htm > > ---------------------------------------------------------------------- > For information about J forums see http://www.jsoftware.com/forums.htm ---------------------------------------------------------------------- For information about J forums see http://www.jsoftware.com/forums.htm
