Thanks for the replies, I have decided to use the tracks method. I
appreciate the response.




-----Original Message-----
From: TSListServer [mailto:[EMAIL PROTECTED]]On
Behalf Of [EMAIL PROTECTED]
Sent: Monday, February 12, 2001 5:29 PM
To: Multiple recipients of list proteledausers
Subject: Re: [PROTEL EDA USERS]: Inner Power Plane clearances




I place a track (maybe 20 mil) on each power plane around the edge of the
outline
of the board to prevent the power planes from extending too far.


_______________________________________________________________

Clive Broome
IDT Sydney Design Centre        Ph:         +61 2 9763 3513
8 Bayswater Dr, Homebush        Fax:        +61 2 9763 3409
Sydney,  NSW, 2127              Email:[EMAIL PROTECTED]
Australia

         Australia's Leading Semiconductor Designers
---------------------------------------------------------------








"Micky Blain" <[EMAIL PROTECTED]> on 02/13/2001 07:32:56 AM

Please respond to [EMAIL PROTECTED]

To:   Multiple recipients of list proteledausers
      <[EMAIL PROTECTED]>
cc:    (bcc: Clive Broome/sdc)

Subject:  [PROTEL EDA USERS]:  Inner Power Plane clearances



1. just go bit on a big order with power plane clearance. It seems that the
gerbers generates the plane all the way to the edge of the keep out layers.
Is there anyway to control the power plane and manually draw them in without
doing them by split planes?

Micky Blain





* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*  This message sent by: PROTEL EDA USERS MAILING LIST
*
*  Use the "reply" command in your email program to
*  respond to this message.
*
*  To unsubscribe from this mailing list use the form at
*  the Association web site. You will need to give the same
*  email address you originally used to subscribe (do not
*  give an alias unless it was used to subscribe).
*
*  Visit http://www.techservinc.com/protelusers/subscrib.html
*  to unsubscribe or to subscribe a new email address.
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *








* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*  This message sent by: PROTEL EDA USERS MAILING LIST
*
*  Use the "reply" command in your email program to
*  respond to this message.
*
*  To unsubscribe from this mailing list use the form at
*  the Association web site. You will need to give the same
*  email address you originally used to subscribe (do not
*  give an alias unless it was used to subscribe).
*
*  Visit http://www.techservinc.com/protelusers/subscrib.html
*  to unsubscribe or to subscribe a new email address.
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *



* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*  This message sent by: PROTEL EDA USERS MAILING LIST
*
*  Use the "reply" command in your email program to
*  respond to this message.
*
*  To unsubscribe from this mailing list use the form at
*  the Association web site. You will need to give the same
*  email address you originally used to subscribe (do not
*  give an alias unless it was used to subscribe).
*
*  Visit http://www.techservinc.com/protelusers/subscrib.html
*  to unsubscribe or to subscribe a new email address.
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

________________________________________________________

To leave the EDAFORUM discussion list, send a email with
'leave edaforum' in the body to '[EMAIL PROTECTED]'

More Information : http://www.dolist.net

Reply via email to