Protel has been able to duplicate the problem.. they are reporting it to
engineering. 
I don't know yet if it causes any other problems.. just the confusion in
reading the drill table...
- Bill Brooks


-----Original Message-----
From: Dennis Saputelli [mailto:[EMAIL PROTECTED]]
Sent: Wednesday, February 28, 2001 4:04 PM
To: Multiple recipients of list proteledausers
Subject: Re: [PROTEL EDA USERS]: Problem with the DRILL Drawing table -
Protel 99SE SP6


I think we heard this about SP6
does the .DRR file look correct?
I think maybe it's "just" the gerber plots

Dennis Saputelli


"Brooks,Bill" wrote:
> 
> I just installed the SP6 on our Protel 99SE software a week ago... We use
> the "size of hole" string as the code for the hole location on our drill
> drawings. Up until now we have had no problems with this... Today I
> discovered a bug. I was getting ready to send out a board and looked at
the
> drill table or Hole Chart if you will, and noticed that the codes for the
> holes were scrambled.. They look like they are right on the board but the
> chart is messed up. Here's what I got...
> --------------------------------------------------------------------
> 125     45      14mil   0.3556mm        PTH
> 32      6       32mil   0.8128mm        PTH
> 55      12      35mil   0.889mm PTH
> 35      27      40mil   1.016mm PTH
> 14      8       55mil   1.397mm PTH
> 40      6       125mil  3.175mm PTH
>         104     Total
> --------------------------------------------------------------------
>         HOLE CHART
> 
> Here's what's in the Drill report
> 
>
---------------------------------------------------------------------------
> NCDrill File Report For: 738481q3.pcb   23-Feb-2001  11:57:15
>
---------------------------------------------------------------------------
> 
> Layer Pair : TopLayer to BottomLayer
> ASCII File : NCDrillOutput.TXT
> EIA File   : NCDrillOutput.DRL
> 
> Tool         Hole Size          Hole Count Plated       Tool Travel
>
---------------------------------------------------------------------------
> T1        14mil (0.3556mm)         45               14.76 Inch (374.88 mm)
> T2        32mil (0.8128mm)         6                6.86 Inch (174.37 mm)
> T3        35mil (0.889mm)          12               5.29 Inch (134.48 mm)
> T4        40mil (1.016mm)          27               11.14 Inch (282.85 mm)
> T5        55mil (1.397mm)          8                10.79 Inch (274.04 mm)
> T6        125mil (3.175mm)         6                21.52 Inch (546.63 mm)
>
---------------------------------------------------------------------------
> Totals                             104              70.36 Inch (1787.25
mm)
> 
> Total Processing Time : 00:00:03
> 
>
----------------------------------------------------------------------------
-- 
___________________________________________________________________________
www.integratedcontrolsinc.com            Integrated Controls, Inc.    
   tel: 415-647-0480                        2851 21st Street          
      fax: 415-647-3003                        San Francisco, CA 94110

* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*  This message sent by: PROTEL EDA USERS MAILING LIST
*
*  Use the "reply" command in your email program to
*  respond to this message.
*
*  To unsubscribe from this mailing list use the form at
*  the Association web site. You will need to give the same
*  email address you originally used to subscribe (do not
*  give an alias unless it was used to subscribe).
*
*  Visit http://www.techservinc.com/protelusers/subscrib.html
*  to unsubscribe or to subscribe a new email address.
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
*  This message sent by: PROTEL EDA USERS MAILING LIST
*
*  Use the "reply" command in your email program to
*  respond to this message.
*
*  To unsubscribe from this mailing list use the form at
*  the Association web site. You will need to give the same
*  email address you originally used to subscribe (do not
*  give an alias unless it was used to subscribe).
*
*  Visit http://www.techservinc.com/protelusers/subscrib.html
*  to unsubscribe or to subscribe a new email address.
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

______________________________________________________
To post a message: <mailto:[EMAIL PROTECTED]>

To unsubscribe or subscribe we recommend using the
form at our web site:
http://www.techservinc.com/protelusers/subscrib.html

You may also unsubscribe directly by email:
<mailto:[EMAIL PROTECTED]?body=leave%20edaforum>
however this may fail if you're trying to unsubscribed
an "old" email address, an alias mail account, or if
your mail client uses an unusual encoding format.

To contact the Forum Administrator:
<mailto:[EMAIL PROTECTED]>

Reply via email to