why not just make a bd with just those holes and give them a second
drill file?
Dennis Saputelli

Brad Velander wrote:
> 
> Rene & others,
>         it is timely that Sean raised this issue because I have been
> fighting with related issues. In my case I have a very complex board outline
> where I have copied the board outline to the bottom layer and made it a
> keepout and control my polygon outlines with respect to the board edge.
> There are associated issues but I get lots of violations that I am trying to
> eliminate with rules, seems to only work part of the time. I also believe
> that I have found a bug relating to polygons while trying to accomplish
> this, I will write about it in a day or two when the crunch is off.
>         In my case I have a number of drill holes at points along the board
> outline. These drills are to relieve the board outline edge where the
> overlying matrix has sharp corners that a router cannot achieve. Thus each
> of these drill holes have no net, no plating, no pad (0mils). Each and
> everyone of them causes a violation with the keepout.
> 
>         The funniest thing is working over several variations of the PCB
> design, some rules work in one copy of the board and while making the
> variations to the next version the same existing rule will quit working all
> of a sudden. I have also had the keepout lines showing violations along the
> entire board outline because they are touching the keepout adjacent to them.
> The listed violation lists the one keepout track segment and it's adjacent
> connected track as the other violator in the pair. Go figure.
> 
>         There are also other cases where a violation is not avoidable, so I
> am trying to devise rules which will eliminate those violations. Sometimes
> the rules work, sometimes they do not. At the moment I have databases which
> have over 300 violations which seem to be indefinable in the DRC rules
> set-up, most all are related to the keepout. I have even tried a rule which
> states the keepout spacing to anything else (Board) is 0mils, no luck.
> 
> Sincerely,
> Brad Velander.
> 
> Lead PCB Designer
> Norsat International Inc.
> #300 - 4401 Still Creek Drive,
> Burnaby, B.C., Canada, V5C 6G9.
> Tel   (604) 292-9089 (direct line)
> Fax  (604) 292-9010
> Website: www.norsat.com
> 
> -----Original Message-----
> From: Rene Tschaggelar [mailto:[EMAIL PROTECTED]]
> Sent: Wednesday, December 12, 2001 8:06 AM
> To: Protel EDA Forum
> Subject: Re: [PEDA] Keepouts & DRC
> 
> You can draw a track manually over a keepout line.
> The DRC signals a violation and you ignore it.
> Is that what you want ?
> 
> Rene
> --
> Ing.Buero R.Tschaggelar - http://www.ibrtses.com
> 
> Sean James wrote:
> >
> > Is there any way to ignore or bypass keepouts during a DRC?
> >

-- 
___________________________________________________________________________
www.integratedcontrolsinc.com            Integrated Controls, Inc.    
   tel: 415-647-0480                        2851 21st Street          
      fax: 415-647-3003                        San Francisco, CA 94110

* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* To post a message: mailto:[EMAIL PROTECTED]
*
* To leave this list visit:
* http://www.techservinc.com/protelusers/leave.html
*
* Contact the list manager:
* mailto:[EMAIL PROTECTED]
*
* Forum Guidelines Rules:
* http://www.techservinc.com/protelusers/forumrules.html
*
* Browse or Search previous postings:
* http://www.mail-archive.com/proteledaforum@techservinc.com
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

Reply via email to