i just rcvd my CD today
i assume it is the same as the demo, i have not looked at it

the registration comes under separate cover by mail, so no use opening
it i guess

Dennis Saputelli

Tony Karavidas wrote:
> 
> This is pure conjecture, but I have a feeling they got DXP out the door
> to meet a business requirement, not an engineering requirement. (Hey, if
> us engineers were in control, we'd probably never ship anything due to
> feature creep and trying to perfect things, so I can see the money side
> of those decisions.
> 
> I would guess they Protel is very active right now at getting out the
> first service pack ASAP. I bet they timed when the first SP would be
> released to the time people had the CD in their hands and had a list of
> complaints about this wide  <-------------------------->
> 
> -----Original Message-----
> From: Tim Hutcheson [mailto:[EMAIL PROTECTED]]
> Sent: Friday, August 09, 2002 1:42 PM
> To: Tim Hutcheson; Protel EDA Forum
> Subject: Re: [PEDA] DXP: Unable to set secondary step Value in Parameter
> Sweep
> 
> Additional note: Problem is related to the fact that the "Sheets to
> Netlist" was set to "Active project" for the project when I started DSP.
> When I switch to "Active sheet", which is what I meant to simulate, the
> signals in the "Available Signals" list do not change to reflect the
> active sheet but remain as they were.  However, if I run the simulation
> anyway, the simulation runs fine, absent the changes I would have made
> if I could pick correct signals.  When the simulation finishes the
> Active signals are correctly displaying the signals of the active sheet
> and I can setup the desired Parameter Sweep selections.
> 
> Hope that clears up my last post.
> 
> More bad news though:  When I tried to do a Secondary sweep with a
> negative step, it flashed a message that looked like it might have been
> the previously mentioned error message about using positive step instead
> and promptly locked up the program.  Had to kill it with task manager.
> 
> Ouch!  Hope my upgrade that I just ordered is a different version than
> the demo!!!!!
> 
> regards,
> 
> Tim Hutcheson
> Research Associate
> Institute for Human and Machine Cognition
> University of West Florida
> 40 S. Alcaniz St.
> Pensacola, FL 32501
> USA
> 805-202-4461
> 
> -----Original Message-----
> From: Tim Hutcheson [mailto:[EMAIL PROTECTED]]
> Sent: Friday, August 09, 2002 3:10 PM
> To: Protel EDA Forum
> Subject: RE: [PEDA] DXP: Unable to set secondary step Value in Parameter
> Sweep
> 
> One obvious problem with DXP is that not all of the Active Signals show
> up in the signal lists after a change.  I'm looking at the lists now and
> the schematic.  I have a resistive element called Rtactor which is part
> of the load and it doesn't appear in the list but another resistor
> called Rlim does.  Setup is "Collect Data For Active Signals", Sheets to
> Nelist Activeis "Active sheet", SimView Setup "Show Active Signals".
> Hard to pick them for Parameter Sweep when they aren't in the drop-down
> pick list!
> 
> Solution:  Run the simulation once and then come back to the dialog -
> All the signals are now there!  So there is an initialization problem -
> if you change anything in the shcematic that changes signal names, you
> have to remember to run the sim once to flush the signal names through,
> then setup the sweep again.
> 
> SoWorks fine with 99SE though.
> 
> regards,
> 


************************************************************************
* Tracking #: BDA31F2BFF5DF0408A0266D8E0C4F3FE8700013E
*
************************************************************************
-- 
___________________________________________________________________________
www.integratedcontrolsinc.com            Integrated Controls, Inc.    
   tel: 415-647-0480                        2851 21st Street          
      fax: 415-647-3003                        San Francisco, CA 94110

* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* To post a message: mailto:[EMAIL PROTECTED]
*
* To leave this list visit:
* http://www.techservinc.com/protelusers/leave.html
*
* Contact the list manager:
* mailto:[EMAIL PROTECTED]
*
* Forum Guidelines Rules:
* http://www.techservinc.com/protelusers/forumrules.html
*
* Browse or Search previous postings:
* http://www.mail-archive.com/proteledaforum@techservinc.com
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

Reply via email to