> http://www.kronjaeger.com/hv/
This guy is nuts...  Check out his 300KV supply.


____________
Brian Guralnick
[EMAIL PROTECTED]



----- Original Message ----- 
From: "Tim Exley" <[EMAIL PROTECTED]>
To: "'Protel EDA Forum'" <[EMAIL PROTECTED]>
Sent: Thursday, January 16, 2003 4:44 PM
Subject: Re: [PEDA] SV: High Voltage power supply


> As BrianG points out, the answer to your question depends a lot on your
> application.  Try searching the web for high voltage supplies ... the
> following may offer some starting points ...
> 
> http://www.powerdesigners.com/cgibin/design_center/Subject
> http://www.kronjaeger.com/hv/
> http://www.high-voltage-assoc.com/cgi-bin/ultimatebb.cgi
> http://www.geocities.com/CapeCanaveral/Lab/5322/hv2.html
> http://www.epanorama.net/links/psu.html
> 
> 
> 
> 
> -----Original Message-----
> From: Brian Guralnick [mailto:[EMAIL PROTECTED]]
> Sent: Thursday, 16 January 2003 6:33 p.m.
> To: Protel EDA Forum
> Subject: Re: [PEDA] SV: High Voltage power supply
> 
> 
> 8Kv at what current?  Pulsed, or continuous?  How fast doest it need to
> build a charge?  I'm thinking along the lines of a small
> transformer switched with diode / cap multiplier at the output.  Something
> similar to an air ionizer circuit.  You'll need to use
> conformal coating all over your PCB.  Will the output be current limited by
> a series resistor?
> 
> 
> ____________
> Brian Guralnick
> [EMAIL PROTECTED]
> 
> 
> ----- Original Message -----
> From: "Peder K. Hellegaard" <[EMAIL PROTECTED]>
> To: "Protel EDA Forum" <[EMAIL PROTECTED]>
> Sent: Wednesday, January 15, 2003 5:16 PM
> Subject: [PEDA] SV: High Voltage power supply
> 
> 
> > 8kV is needed......
> >
> >
> >
> > -----Oprindelig meddelelse-----
> > Fra: Brian Guralnick [mailto:[EMAIL PROTECTED]]
> > Sendt: 15. januar 2003 23:03
> > Til: Protel EDA Forum
> > Emne: Re: [PEDA] High Voltage power supply
> >
> >
> > How high?
> >
> > 25Kv, 100Kv?
> >
> > Or, 600v.
> >
> > In both cases, a flyback will probably be the cheapest & most cost
> > effective.
> >
> >
> > ____________
> > Brian Guralnick
> > [EMAIL PROTECTED]
> >
> >
> > ----- Original Message -----
> > From: "Peder K. Hellegaard" <[EMAIL PROTECTED]>
> > To: "Protel EDA Forum" <[EMAIL PROTECTED]>
> > Sent: Wednesday, January 15, 2003 9:19 AM
> > Subject: [PEDA] High Voltage power supply
> >
> >
> > > Anyone who knows where to find schematics for high voltage (low current)
> > > power supplies, preferably designed with a series of voltage doublers ?
> > >
> > >
> > > Thanks in advance......
> > >
> > >
> > >
> > > Peter
> > >
> > >
> > >
> > >

* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* To post a message: mailto:[EMAIL PROTECTED]
*
* To leave this list visit:
* http://www.techservinc.com/protelusers/leave.html
*
* Contact the list manager:
* mailto:[EMAIL PROTECTED]
*
* Forum Guidelines Rules:
* http://www.techservinc.com/protelusers/forumrules.html
*
* Browse or Search previous postings:
* http://www.mail-archive.com/proteledaforum@techservinc.com
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

Reply via email to