Perhaps you need to change or add this feature in the network interface file:
https://pve.proxmox.com/wiki/Upgrade_from_6.x_to_7.0#Linux_Bridge_MAC-Address_Change --- Gilberto Nunes Ferreira (47) 99676-7530 - Whatsapp / Telegram Em qua., 21 de jul. de 2021 às 12:18, Uwe Sauter <[email protected]> escreveu: > Hi all, > > Fresh installation of PVE 7 with all available updates. > > It looks like I'm unable to configure bonding of two interfaces using LCAP. > > Output from "ip a": > 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group > default qlen 1000 > link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 > inet 127.0.0.1/8 scope host lo > valid_lft forever preferred_lft forever > inet6 ::1/128 scope host > valid_lft forever preferred_lft forever > 2: eno1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq master > vmbr1224 state UP group default > qlen 1000 > link/ether a4:bf:01:2f:63:f2 brd ff:ff:ff:ff:ff:ff > altname enp24s0f0 > 3: enp59s0f4: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 qdisc mq state UP > group default qlen 1000 > link/ether 00:07:43:18:82:70 brd ff:ff:ff:ff:ff:ff > inet6 fe80::207:43ff:fe18:8270/64 scope link > valid_lft forever preferred_lft forever > 4: enp59s0f4d1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 9000 qdisc mq state > UP group default qlen 1000 > link/ether 00:07:43:18:82:78 brd ff:ff:ff:ff:ff:ff > inet6 fe80::207:43ff:fe18:8278/64 scope link > valid_lft forever preferred_lft forever > 5: eno2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group > default qlen 1000 > link/ether a4:bf:01:2f:63:f3 brd ff:ff:ff:ff:ff:ff > altname enp24s0f1 > 6: ibp94s0: <BROADCAST,MULTICAST> mtu 2044 qdisc noop state DOWN group > default qlen 256 > link/infiniband > 80:00:0a:08:fe:80:00:00:00:00:00:00:f4:52:14:03:00:2c:14:51 brd > 00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff > 7: ibp94s0d1: <BROADCAST,MULTICAST> mtu 2044 qdisc noop state DOWN group > default qlen 256 > link/infiniband > 80:00:0a:09:fe:80:00:00:00:00:00:00:f4:52:14:03:00:2c:14:52 brd > 00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff > 8: vmbr1224: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue > state UP group default qlen 1000 > link/ether a4:bf:01:2f:63:f2 brd ff:ff:ff:ff:ff:ff > inet 10.224.203.1/16 scope global vmbr1224 > valid_lft forever preferred_lft forever > inet6 fe80::a6bf:1ff:fe2f:63f2/64 scope link > valid_lft forever preferred_lft forever > > > My current /etc/network/interfaces, which is missing the bridges for the > VMs: > auto lo > iface lo inet loopback > > auto eno1 > iface eno1 inet manual > > auto enp59s0f4 > iface enp59s0f4 inet manual > mtu 9000 > > auto enp59s0f4d1 > iface enp59s0f4d1 inet manual > mtu 9000 > > auto bond0 > iface bond0 inet manual > slaves enp59s0f4 enp59s0f4d1 > bond-downdelay 200 > bond-miimon 100 > bond-mode 802.3ad > bond-updelay 200 > > auto vmbr1224 > iface vmbr1224 inet static > address 10.224.203.1 > netmask 255.255.0.0 > gateway 10.224.200.1 > bridge_ports eno1 > bridge_stp off > bridge_fd 0 > > ## # VLAN 155 nativ on bond0 > ## auto vmbr155 > ## iface vmbr155 inet manual > ## mtu 9000 > ## bridge_ports bond0 > ## bridge_stp off > ## bridge_fd 0 > > > This config was copied over from the PVE 6 installation on the same host > which experienced a SSD > failure and thus was re-installed with PVE 7. > > > Am I missing something? Am I being blind? > > > Any help is appreciated. > > > Thanks, > > Uwe > > > > > _______________________________________________ > pve-user mailing list > [email protected] > https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user > > _______________________________________________ pve-user mailing list [email protected] https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user
