Hello, I am attempting to use a Hauppauge wintv-hvr-1950 model USB capture device to capture composite video input to a Beagleboard running Angstrom linux kernel version 2.6.28. I was able to successfully get this to work on a regular i386 machine with Ubuntu Intrepid, but when I try to cp /dev/video0 to a file on the Beagleboard, it fails. I'm hoping that someone here can shed some light on what might be going wrong. I'm doing this all from the serial console. Here's a log of what's happening, from the time I plug in the device to the USB port to the errors at the end, which just repeat until I unplug the hvr-1950:
usb 2-1.3: new high speed USB device using musb_hdrc and address 3 usb 2-1.3: device v2040 p7501 is not supported usb 2-1.3: configuration #1 chosen from 1 choice Linux video capture interface: v2.00 usbcore: registered new interface driver pvrusb2 pvrusb2: V4L in-tree version:Hauppauge WinTV-PVR-USB2 MPEG2 Encoder/Tuner pvrusb2: Debug mask is 31 (0x1f) usb 2-1.3: firmware: requesting v4l-pvrusb2-73xxx-01.fw pvrusb2: Device microcontroller firmware (re)loaded; it should now reset and reconnect. usb 2-1.3: USB disconnect, address 3 pvrusb2: Device being rendered inoperable usb 2-1.3: new high speed USB device using musb_hdrc and address 4 usb 2-1.3: device v2040 p7501 is not supported usb 2-1.3: configuration #1 chosen from 1 choice cx25840' 2-0044: cx25843-24 found @ 0x88 (pvrusb2_a) tuner' 2-0042: chip found @ 0x84 (pvrusb2_a) tveeprom 2-00a2: Hauppauge model 75111, rev C3E9, serial# 5371393 tveeprom 2-00a2: MAC address is 00-0D-FE-51-F6-01 tveeprom 2-00a2: tuner model is Philips 18271_8295 (idx 149, type 54) tveeprom 2-00a2: TV standards NTSC(M) ATSC/DVB Digital (eeprom 0x88) tveeprom 2-00a2: audio processor is CX25843 (idx 37) tveeprom 2-00a2: decoder processor is CX25843 (idx 30) tveeprom 2-00a2: has radio, has IR receiver, has IR transmitter pvrusb2: Supported video standard(s) reported available in hardware: PAL-M/N/Nc;NTSC-M/Mj/Mk;ATSC-8VSB/16VSB pvrusb2: Mapping standards mask=0x300b700 (PAL-M/N/Nc;NTSC-M/Mj/Mk;ATSC-8VSB/16VSB) pvrusb2: Setting up 6 unique standard(s) pvrusb2: Set up standard idx=0 name=PAL-M pvrusb2: Set up standard idx=1 name=PAL-N pvrusb2: Set up standard idx=2 name=PAL-Nc pvrusb2: Set up standard idx=3 name=NTSC-M pvrusb2: Set up standard idx=4 name=NTSC-Mj pvrusb2: Set up standard idx=5 name=NTSC-Mk pvrusb2: Initial video standard (determined by device type): NTSC-M pvrusb2: Device initialization completed successfully. pvrusb2: registered device video0 [mpeg] DVB: registering new adapter (pvrusb2-dvb) cx25840' 2-0044: firmware: requesting v4l-cx25840.fw cx25840' 2-0044: loaded v4l-cx25840.fw firmware (16382 bytes) cx25840' 2-0044: 0x0000 is not a valid video input! tda829x 2-0042: setting tuner address to 60 tda18271 2-0060: creating new instance TDA18271HD/C1 detected @ 2-0060 tda829x 2-0042: type set to tda8295+18271 cx25840' 2-0044: Video signal: not present cx25840' 2-0044: Detected format: PAL-BDGHI cx25840' 2-0044: Specified standard: NTSC-M cx25840' 2-0044: Specified video input: Composite 7 cx25840' 2-0044: Specified audioclock freq: 48000 Hz cx25840' 2-0044: Detected audio mode: forced mode cx25840' 2-0044: Detected audio standard: forced audio standard cx25840' 2-0044: Audio muted: no cx25840' 2-0044: Audio microcontroller: stopped cx25840' 2-0044: Configured audio standard: automatic detection cx25840' 2-0044: Configured audio system: BTSC cx25840' 2-0044: Specified audio input: External cx25840' 2-0044: Preferred audio mode: stereo cx25840' 2-0044: 0x0000 is not a valid video input! DVB: registering adapter 0 frontend 0 (Samsung S5H1411 QAM/8VSB Frontend)... tda829x 2-0042: type set to tda8295 tda18271 2-0060: attaching existing instance r...@beagleboard:/# echo composite > /sys/class/pvrusb2/sn-5371393/ctl_input/cur _val cx25840' 2-0044: firmware: requesting v4l-cx25840.fw cx25840' 2-0044: loaded v4l-cx25840.fw firmware (16382 bytes) usb 2-1.3: firmware: requesting v4l-cx2341x-enc.fw r...@beagleboard:/# cp /dev/video0 /home/root/test.mpeg pvrusb2: ***WARNING*** device's encoder appears to be stuck (status=0x00000003) pvrusb2: Encoder command: 0xdc pvrusb2: Giving up on command. This is normally recovered by the driver. pvrusb2: Failed to configure cx23416 usb 2-1.3: firmware: requesting v4l-cx2341x-enc.fw pvrusb2: ***WARNING*** device's encoder appears to be stuck (status=0x00000003) pvrusb2: Encoder command: 0xdc pvrusb2: Giving up on command. This is normally recovered by the driver. pvrusb2: Failed to configure cx23416 usb 2-1.3: firmware: requesting v4l-cx2341x-enc.fw pvrusb2: ***WARNING*** device's encoder appears to be stuck (status=0x00000003) pvrusb2: Encoder command: 0xdc pvrusb2: Giving up on command. This is normally recovered by the driver. pvrusb2: Failed to configure cx23416 usb 2-1.3: firmware: requesting v4l-cx2341x-enc.fw pvrusb2: ***WARNING*** device's encoder appears to be stuck (status=0x00000003) pvrusb2: Encoder command: 0xdc pvrusb2: Giving up on command. This is normally recovered by the driver. pvrusb2: Failed to configure cx23416 usb 2-1.3: firmware: requesting v4l-cx2341x-enc.fw pvrusb2: ***WARNING*** device's encoder appears to be stuck (status=0x00000003) pvrusb2: Encoder command: 0xdc pvrusb2: Giving up on command. This is normally recovered by the driver. pvrusb2: Failed to configure cx23416 usb 2-1.3: firmware: requesting v4l-cx2341x-enc.fw pvrusb2: ***WARNING*** device's encoder appears to be stuck (status=0x00000003) pvrusb2: Encoder command: 0xdc pvrusb2: Giving up on command. This is normally recovered by the driver. pvrusb2: Failed to configure cx23416 usb 2-1.3: firmware: requesting v4l-cx2341x-enc.fw pvrusb2: ***WARNING*** device's encoder appears to be stuck (status=0x00000003) pvrusb2: Encoder command: 0xdc pvrusb2: Giving up on command. This is normally recovered by the driver. pvrusb2: Failed to configure cx23416 usb 2-1.3: firmware: requesting v4l-cx2341x-enc.fw pvrusb2: ***WARNING*** device's encoder appears to be stuck (status=0x00000003) pvrusb2: Encoder command: 0xdc pvrusb2: Giving up on command. This is normally recovered by the driver. pvrusb2: Failed to configure cx23416 usb 2-1.3: firmware: requesting v4l-cx2341x-enc.fw I appreciate any assistance. _______________________________________________ pvrusb2 mailing list [email protected] http://www.isely.net/cgi-bin/mailman/listinfo/pvrusb2
