* Greg Kurz (gr...@kaod.org) wrote: > On Wed, 7 Feb 2018 15:55:01 +0000 > "Dr. David Alan Gilbert" <dgilb...@redhat.com> wrote: > > > * Greg Kurz (gr...@kaod.org) wrote: > > > This capability must have the same value on both source and destination, > > > otherwise migration fails (commit 875fcd013ab6 "migration: incoming > > > postcopy advise sanity checks"). > > > > > > Let's write it down in various places where postcopy-ram is documented. > > > > > > Signed-off-by: Greg Kurz <gr...@kaod.org> > > > > Thanks, > > > > Reviewed-by: Dr. David Alan Gilbert <dgilb...@redhat.com> > > > > Who should pick this up ?
I was going to pick it up in a migration pull today. Dave > > > --- > > > docs/devel/migration.rst | 4 ++-- > > > hmp-commands.hx | 3 ++- > > > qapi/migration.json | 10 ++++++---- > > > 3 files changed, 10 insertions(+), 7 deletions(-) > > > > > > diff --git a/docs/devel/migration.rst b/docs/devel/migration.rst > > > index bf97080dac2f..9d1b7657f0cf 100644 > > > --- a/docs/devel/migration.rst > > > +++ b/docs/devel/migration.rst > > > @@ -387,8 +387,8 @@ doesn't finish in a given time the switch is made to > > > postcopy. > > > Enabling postcopy > > > ----------------- > > > > > > -To enable postcopy, issue this command on the monitor prior to the > > > -start of migration: > > > +To enable postcopy, issue this command on the monitor (both source and > > > +destination) prior to the start of migration: > > > > > > ``migrate_set_capability postcopy-ram on`` > > > > > > diff --git a/hmp-commands.hx b/hmp-commands.hx > > > index 15620c94d3fc..d26eb4119b9d 100644 > > > --- a/hmp-commands.hx > > > +++ b/hmp-commands.hx > > > @@ -1041,7 +1041,8 @@ ETEXI > > > .params = "", > > > .help = "Followup to a migration command to switch the > > > migration" > > > " to postcopy mode. The postcopy-ram capability > > > must " > > > - "be set before the original migration command.", > > > + "be set on both source and destination before the " > > > + "original migration command .", > > > .cmd = hmp_migrate_start_postcopy, > > > }, > > > > > > diff --git a/qapi/migration.json b/qapi/migration.json > > > index 4cd3d1315884..7f465a1902ce 100644 > > > --- a/qapi/migration.json > > > +++ b/qapi/migration.json > > > @@ -327,8 +327,10 @@ > > > # to speed up convergence of RAM migration. (since 1.6) > > > # > > > # @postcopy-ram: Start executing on the migration target before all of > > > RAM has > > > -# been migrated, pulling the remaining pages along as needed. > > > NOTE: If > > > -# the migration fails during postcopy the VM will fail. (since > > > 2.6) > > > +# been migrated, pulling the remaining pages along as needed. > > > The > > > +# capacity must have the same setting on both source and target > > > +# or migration will not even start. NOTE: If the migration > > > fails during > > > +# postcopy the VM will fail. (since 2.6) > > > # > > > # @x-colo: If enabled, migration will never end, and the state of the VM > > > on the > > > # primary side will be migrated continuously to the VM on > > > secondary > > > @@ -742,8 +744,8 @@ > > > # @migrate-start-postcopy: > > > # > > > # Followup to a migration command to switch the migration to postcopy > > > mode. > > > -# The postcopy-ram capability must be set before the original migration > > > -# command. > > > +# The postcopy-ram capability must be set on both source and destination > > > +# before the original migration command. > > > # > > > # Since: 2.5 > > > # > > > > > -- > > Dr. David Alan Gilbert / dgilb...@redhat.com / Manchester, UK > > > -- Dr. David Alan Gilbert / dgilb...@redhat.com / Manchester, UK