Is it working now, or still not working?
I don't recall precisely what might have happened that caused it to work
ok after this failure, except possibly a reboot.
You should run
# yum update
and reboot before running the latest qtp-newmodel.
Patrick Ring wrote:
On the attempt (to run newmodel) where I had run the yum update, I did
reboot after it was complete.
I'm fairly certain I rebooted after the QMT ISO finished the install as
well.
In either case I had not done anything between the install and the new
model script besides reboot.
Thanks,
Patrick Ring
--------------------------
Sent from my BlackBerry Wireless Device
-----Original Message-----
From: news <[email protected]>
To: [email protected] <[email protected]>
Sent: Thu Dec 31 17:21:10 2009
Subject: [qmailtoaster] Re: Has something changed in QT?
The fuse subsystem is fairly new to qtp-newmodel. It has been tested on
current CentOS 4.
I seem to remember having the same problem with CentOS5. Have you
rebooted since you updated to the latest kernel?
Patrick Ring wrote:
> I am putting together a virtual (VMWare) with the QmailToaster ISO
> (CentOS 4.X).
>
> I'm having problems with the newmodel script (of QTP) erroring out when
> it goes to mount the sandbox.
> In the past this always worked for me. (In the past I have not used the
> QmailToaster ISO disk...I usually loaded CentOS and then built/loaded QT)
>
> Specifically the errors occur right after
> Installing: fuse
> Installing: kernel-devel
> Installing: dkms
> Installing: fuse-unionfs
> Installing: dkms-fuse
>
> Installed: dkms-fuse.noarch 0:2.7.4-1.nodist.rf fuse-unionfs.i386
> 0:0.23-1.qtp
> Dependancy Installed: dkms.noarch 0:2.0.22.0-1.el4.rf fuse.i386
> 0:2.7.4-1.qtp kernel-devel.i686 0:2.6.9-89.0.18.EL
>
> Then right after it says "Complete!"
> fuse: device not found, try 'modprobe fuse' first
> FATAL: Module fuse not found.
> fuse: device not found, try 'modprobe fuse' first
> fuse: device not found, try 'modprobe fuse' first
> fuse: device not found, try 'modprobe fuse' first
> fuse: device not found, try 'modprobe fuse' first
> fuse: device not found, try 'modprobe fuse' first
> fuse: device not found, try 'modprobe fuse' first
> fuse: device not found, try 'modprobe fuse' first
> fuse: device not found, try 'modprobe fuse' first
> fuse: device not found, try 'modprobe fuse' first
> fuse: device not found, try 'modprobe fuse' first
> fuse: device not found, try 'modprobe fuse' first
> fuse: device not found, try 'modprobe fuse' first
> mount: mount point /mnt/qtp-sandbox/var/lib/rpm does not exist
> cp: '/mnt/qtp-sandbox/var/lib/rpm' : specified directory does not exist
> Try 'cp --help' for more information.
> qtp-mount-sandbox: sandbox was not mounted successfully
>
> qtp-newmodel - qtp-mount-sandbox failed, exiting
>
> Anyway, I've tried to perform newmodel both before and after a "yum
> update", and I stumbled across a previous thread that recommended
> turning off the "autofs" service. No change either way.
>
> Has something changed in the newmodel script? Or is there something
> different between the CentOS/QT from the ISO vs when I load manually?
>
> Please advise.
> Thank you,
> Patrick Ring
>
>
>
> Patrick M. Ring
> P. Ring Technologies
> Louisiana Web Host, LLC.
> 985-868-4200
>
--
-Eric 'shubes'
---------------------------------------------------------------------------------
Qmailtoaster is sponsored by Vickers Consulting Group
(www.vickersconsulting.com)
Vickers Consulting Group offers Qmailtoaster support and installations.
If you need professional help with your setup, contact them today!
---------------------------------------------------------------------------------
Please visit qmailtoaster.com for the latest news, updates, and
packages.
To unsubscribe, e-mail: [email protected]
For additional commands, e-mail:
[email protected]
--
-Eric 'shubes'
---------------------------------------------------------------------------------
Qmailtoaster is sponsored by Vickers Consulting Group
(www.vickersconsulting.com)
Vickers Consulting Group offers Qmailtoaster support and installations.
If you need professional help with your setup, contact them today!
---------------------------------------------------------------------------------
Please visit qmailtoaster.com for the latest news, updates, and packages.
To unsubscribe, e-mail: [email protected]
For additional commands, e-mail: [email protected]
