Just a small followup.
Tried to make the QtMobility_installer.sis by doing the following steps:
1. Cd {qtmobility}\src\s60installs
2. Make sis qtmobility_installer.pkg
3. Signsis qtmobility_installer.sis qtmobility_installer.sisx
Mycertificate.cer My.key MyPassword
It worked fine, needed to copy smartinstaller.sis from NokiaQtSdk to Qt 4.7.0
RC folder, but else it was fine.
Installing it on my Nokia E52 device, the smartinstaller looked for QtMobility
"somewhere" (don't know where smartinstaller goes to), found QtMobility 1.1 and
installed it. And identifying the QtMobilty already on the phone.
But still, when trying to install Camera example, the phone tells me QtMobility
1.1 is not installed.
So now I'm a bit more confident that I am doing the right things, but something
is wrong with the Id's of the different packages.
Any gueses anyone? (qualified knowledge will do as well ) ;-)
/Anders
From: [email protected]
[mailto:[email protected]] On Behalf Of Anders
Kjærgaard Hansen
Sent: 21. september 2010 07:57
To: Luoma Antti; [email protected]
Subject: Re: [Qt-mobility-feedback] Do there exist a prebuilt sis file for
QtMobility 1.1 TP?
Have now fetched the head/master revision (from the
http://qt.gitorious.org/qt-mobility/qt-mobility/trees/HEAD though).
It configures and compiles fine (have only tried with "-modules multimedia",
but all seems to be fine.)
Until I want to run the camera example that is. ;-)
In the emulator (in Carbide), it boots, and load, and then panics.
On the device it still reports 'Component QtMobility missing. Continue
anyway?'. I have done the 'make sis' step, and have installed QtMobility.sis
file on the device. And if I try to reinstall it, it says it is already
installed. My best guess would be that QtMobility uses another ID to install
itself than the id the other packages look for. But when I investigate the pkg
files it seems to be the same Id all over (0x2002AC89).
If I continue and install it, the camera example panics on startup and never
gets started.
So it seemed better, but I must still be missing something.
Trying to install qtmultimediakit_ecamengine.sis (or a signed sisx), once again
gives me a warning about QtMobility not installed, and during install I get an
update error. Looking at the src\s60installs\QtMobility_template.pkg, it seems
like the ecamengine should be included automatically.
But clearly I'm missing something.
Any good ideas out there?
/Anders
From: Luoma Antti [mailto:[email protected]]
Sent: 20. september 2010 12:59
To: Anders Kjærgaard Hansen; [email protected]
Subject: RE: [Qt-mobility-feedback] Do there exist a prebuilt sis file for
QtMobility 1.1 TP?
Hi,
Just realized that symbian Camera backend wasn't available in qtmobility 1.1
TP. So I am not amazed that id doesn't work :-). Backend is located in
plugins\multimedia\symbian\ecam
For camera to work you will need newer code. You have to get it from gitorious
via git and compile that again. This isn't released just yet so there might be
some bugs still, but if there are bugs, please report those also.
Magic command for getting the code..
"git clone git://gitorious.org/qt-mobility/qt-mobility.git"
-antti
________________________________
From: [email protected]
[mailto:[email protected]] On Behalf Of Anders
Kjærgaard Hansen
Sent: Friday, September 17, 2010 3:56 PM
To: Anders Kjærgaard Hansen; [email protected]
Subject: Re: [Qt-mobility-feedback] Do there exist a prebuilt sis file for
QtMobility 1.1 TP?
The rest of the mail follows here - damn keyboard shortcuts...
Hi all
Now the week are about to end, and I'm still struggling getting QtMobility 1.1
TP running on my device.
So my question now is... Can anyone in the community send me a working sis file
able to install QtMobility 1.1 TP on a device?
Below is a resume of where I am standing now.
To sum up, my situation is this:
1. I have successfully installed Qt 4.7 RC, and QtMobility 1.1 TP on my
machine. QtMobility configured to only use Multimedia module.
2. I can compile the Camera Sample, and I can build my own small samples
using Multimedia module, and including Camera.
3. I can create sis files that run on phone (when not instantiating a
Camera object)
a. This sample compiles, and installs (With warning that QtMobility is
not installed - even though it is) and runs on my device:
#include "JustHello.h"
#include <qmessagebox.h>
#include <qcamera.h>
JustHello::JustHello(QWidget *parent)
: QMainWindow(parent)
{
ui.setupUi(this);
QMessageBox::information(this, "JustHello", "App
started");
// camera = new QCamera();
}
b. This sample compiles, installs (with warning that QtMobility is not
installed - even though it is), but panics at startup.
#include "JustHello.h"
#include <qmessagebox.h>
#include <qcamera.h>
JustHello::JustHello(QWidget *parent)
: QMainWindow(parent)
{
ui.setupUi(this);
QMessageBox::information(this, "JustHello", "App
started");
camera = new QCamera();
}
My QtMobility.sis file installs, but subsequently installs of applications with
QtMobility 1.1 as prerequisite reports that QtMobility is not installed.
I really hope somebody can take 10 seconds of their time to send me their sis
file.. ;-)
Have a nice weekend
/Anders
_______________________________________________
Qt-mobility-feedback mailing list
[email protected]
http://lists.trolltech.com/mailman/listinfo/qt-mobility-feedback
