You should have no connection between terminal 1 and anything else with no connections to the starter so that's certainly your problem. With the link cable to the actual motor disconnected you shouldn't have any connection between 1 or 3 and the metalwork either, only 2 should have a connection to the metalwork.
Something funny is going on but i can't think what. FWIW i've never had this problem or even heard of it before. The normal problem with these starters is turning over slowly when hot. The connection next to terminal 3 under the paint is a bit strange as the other side of the solenoid coil is earthed and the connections to 1 and 3 are made directly on the back of the studs that the wires are bolted to. I wonder if Q&H have had a bad batch of recon starters, maybe the solenoids have been assembled wrong. If you can i'd take it back and see if they will swap it for a different make. Jim Steve Kodz wrote: > OK I disconnected all the connections, except for the main +ve feed from the > battery and the motor still spins, so I guess it's the solenoid that has > shorted?!? > > I have removed the starter from the car and I get continuity between all the > terminals 1, 2 & 3 in the photo and also to the metal casing. This is a > brand new QH starter that has done exactly the same and in a similar milage > <10 miles as the previous replacement, so I don't think replacing it again > will help. > > www.h4-turbo.co.uk/img/StarterMotorConnections.jpg > > Argh! This car is driving me mad now :( > > Regards, > Steve > > On Saturday 19 Sep 2009, Jim Hearne wrote: > >> Thats an interesting one. >> There is only one wire to the starter to turn it over, the wire powers >> up the solenoid on the starter which both engages the starter with the >> flywheel and connects the power to the starter motor itself. >> Think of the solenoid as a relay for the starter power plus it moves the >> gear into mesh. >> >> So, if the starter motor is spinning but it's not turning the engine >> over it's one of 2 things. >> Either there is a short on the starter solenoid between the 2 big >> terminals or there is power to the small terminal on the starter but >> it's not a high enough voltage to pull the solenoid far enough for it to >> engage with the ring gear. >> >> The easiest test is to pull the small wire off the starter solenoid >> while this problem is occurring (the starter is spinning). >> If the starter keeps going then it's the first cause and if it keeps >> going it's the second. >> >> If it keeps going check that the 2 big wires aren't shorting, there is a >> plastic "bridge" moulded into the solenoid to stop this but it often >> breaks away and the wires can short. Otherwise it must be internal to >> the solenoid. >> >> If it stops then go back to the ignition switch, does the starter stop >> spinning if you unplug the ignition switch connector ?, if so it could >> be a fault ignition switch. >> In between that is just the immobiliser and maybe a link in the fuse >> box, check for a relay position with a metal link fitted instead of a >> relay (this has a relay that disables the starter on a car with a auto >> gearbox). If you have the link it could be a short inside the fusebox. >> >> Jim >> >> Steve Kodz wrote: >> >>> This is now the second starter motor where I've had this problem, so >>> I'm starting to think it's the car and not the starter. >>> >>> With the battery connected and no ignition power the starter motor runs >>> constantly - the only way to stop it is to disconnect the battery. The >>> starter is not engaging the flywheel, so it's not trying to turn over >>> the engine. It had been running fine for about half a day before this >>> and the only common thing with the previous starter is that both hadn't >>> been on the car that long and showed the problem after the engine got >>> hot, however I now have the current starter wrapped in a flexible head >>> shield. >>> >>> There is an immobiliser on the car that immobilises the starter motor >>> as one of the 2 circuits, so could this potentially be the cause? >>> >>> The car is my H4 with it's CVH turbo engine using the EFi management >>> from the FRST donor. >>> >>> Any help will be appreciated as I need to sort this out to get the car >>> to it's MoT retest next week - it only failed because the rear brake >>> cylinders had seized, which wasn't bad seeing the car hadn't moved >>> since may! >>> >>> Regards, >>> Steve >>> > > > --~--~---------~--~----~------------~-------~--~----~ You received this message because you are subscribed to the Google Groups "Quantum Owners Group" group. To post to this group, send email to [email protected] To unsubscribe from this group, send email to [email protected] For more options, visit this group at http://groups.google.com/group/quantumowners?hl=en IMPORTANT NOTE: All information presented herewith is provided on an "As Is" basis, without warranty or the implication thereof. Neither the Quantum Owners Club nor the individuals associated with the Quantum Owners Club or in the preparation of the above information shall have any liability to any person or entity with respect to liability, loss, or damage caused or alleged to be caused directly or indirectly by the instructions contained within this or related message(s). -~----------~----~----~----~------~----~------~--~---
