Count me in for both. I have replaced the the rear window but not put the rubber back as was too badly damaged & didn't find anything suitable to replace it with.
I must have an early mk2 saloon as have the mentioned front supension fixing. Not yet taken the springs/struts off as yet but would be good to know where I could get replacement parts if required. Don't think it will be long before they might need replacing. Mark On Mar 2, 9:23 am, "Andy Heaton" <[email protected]> wrote: > Dave. > > I think we had better have a word with Kenny Monkman to see if he could turn > some in stainless steel, if its possible ? as the mk1s 003 and mine 016 need > the same, of course their are the early mk2 saloons with the same set up so > we may find it would be cost effective to produce and then have a batch we > can sell on to other fiesta owners as well as for our Q's. > > The same can be said for the rear window rubbers i.e. chevette. we have a > company in Kent who can reproduce these seals and any other unusual seal. > > Andy h. > > > > ----- Original Message ----- > From: "Dave the Subbie" <[email protected]> > To: "Quantum Owners Group" <[email protected]> > Sent: Wednesday, March 02, 2011 9:10 AM > Subject: [Quantum Owners] Mk1 Fiesta McPherson struts > > Hi all. I've hit a (minor) brick wall in re-building my Mk1, and I'm > wondering if anyone can help, or suggest where I can get a part from. > > The Front Suspension struts are from a Mk1 Fiesta (the type that > attach to the bodywork by 2 M8 studs). The bit I need is the circular > spacer that locates the top spring mount on the damper rod. It is a > sort of top hat section with a large diameter of 45mm, 5mm thick, and > a small diameter of 26mm, 4mm thick, and 19mm hole through the centre. > I need 2 of them, as they have cracked up on both sides (which > probably explains the 'clonking' the last owner complained of). > > My local Ford dealer identified the part (Cost just over �1 each), but > Ford no longer keep it. The Fiesta Centre don't keep it either. I can > get some machined up, but that will be expensive when compared with > finding some old stock, as I don't have access to a lathe, so I'll > have to pay someone to make them from scratch. > > I know it's an off-chance, but do any of you know where I can get them > from. > > If I do have to get some machined up, then does anyone else need any? > > Dave. > > -- > You received this message because you are subscribed to the Google Groups > "Quantum Owners Group" group. > To post to this group, send email to [email protected] > To unsubscribe from this group, send email to > [email protected] > For more options, visit this group > athttp://groups.google.com/group/quantumowners?hl=en > > IMPORTANT NOTE: All information presented herewith is provided on an "As Is" > basis, without warranty or the implication thereof. Neither the Quantum > Owners Club nor the individuals associated with the Quantum Owners Club or > in the preparation of the above information shall have any liability to any > person or entity with respect to liability, loss, or damage caused or > alleged to be caused directly or indirectly by the instructions contained > within this or related message(s).- Hide quoted text - > > - Show quoted text - -- You received this message because you are subscribed to the Google Groups "Quantum Owners Group" group. To post to this group, send email to [email protected] To unsubscribe from this group, send email to [email protected] For more options, visit this group at http://groups.google.com/group/quantumowners?hl=en IMPORTANT NOTE: All information presented herewith is provided on an "As Is" basis, without warranty or the implication thereof. Neither the Quantum Owners Club nor the individuals associated with the Quantum Owners Club or in the preparation of the above information shall have any liability to any person or entity with respect to liability, loss, or damage caused or alleged to be caused directly or indirectly by the instructions contained within this or related message(s).
