The size difference is between the Mk3 Fiesta and the Mk3.5 Fiesta
They changed quite a few things on the cars then, somewhere in 1994.
The bottom balljoint taper, the number of rivets holding the bottom
balljoint to the wishbone (from 2 to 3), the size of the bottom of the shock
absorber.
And thats just on the front suspension.
Jim
--------------------------------------------------
From: "Critter" <[email protected]>
Sent: Wednesday, February 01, 2012 10:15 PM
To: "Quantum Owners Group" <[email protected]>
Subject: [Quantum Owners] Re: H4 Shocks and springs
Thanks for the reply Gary thats what I thought the set up was.
I will check the size of the bottom of the strut on the front dampers
as I believe thats where the difference lies i.e. larger for the Si ?
I need to get it up on stands and give the suspension agood check over
just a bit cold on the drive at the moment.
Thanks
Trevor
On Jan 31, 8:06 pm, Gary <[email protected]> wrote:
I fitted monroe gas dampers for a 1.1 fiesta and leigsfords (speller??)
springs again 1.1. This was in an attempt to stop the rear tyres rubbing
the arches when the boot had a load in. The handling was not improved or
changed from the factory built set up. even tho one of the original
dampers was leaking the rear tyres still rubbed. So no change to mine.
The consensus from people in the know was Xr2i set up at the front and
1.1 at the rear. Q Stourbridge tried sensatracs and other 'cheap'
alternatives but could not improve on standard ford for a budget set up.
To add ours was built fron a 1.6 Zetec Si and the front corners are
completely different to an Xr2 due to sizes of dampers, wishbone pins
etc. So be careful if sourcing second hand.
Regards
Qless Gary
On 27/01/2012 10:59, Critter wrote:
> Hi Al
> Can you please advise as to the correct/best standard spring and
> damper setup for the H4.
> I have the Zetec Rs1800 engine up front with Avon ZV3 155/55 R14.
> I'm afraid I can't afford an adustable set up at the mo so it will
> have to be standard fiesta springs and shocks.
> I think I saw somewhere that it should be XR2i at the front and 1.1 at
> the rear if so has anyone fitted shorter springs at the front.
> My car seems to be a bit high at the sharp end and is bouncing about
> too much at speed.
> many thanks in advance
> Trevor- Hide quoted text -
- Show quoted text -
--
You received this message because you are subscribed to the Google Groups
"Quantum Owners Group" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to
[email protected]
For more options, visit this group at
http://groups.google.com/group/quantumowners?hl=en
IMPORTANT NOTE: All information presented herewith is provided on an "As
Is" basis, without warranty or the implication thereof. Neither the
Quantum Owners Club nor the individuals associated with the Quantum Owners
Club or in the preparation of the above information shall have any
liability to any person or entity with respect to liability, loss, or
damage caused or alleged to be caused directly or indirectly by the
instructions contained within this or related message(s).
--
You received this message because you are subscribed to the Google Groups "Quantum
Owners Group" group.
To post to this group, send email to [email protected]
To unsubscribe from this group, send email to
[email protected]
For more options, visit this group at
http://groups.google.com/group/quantumowners?hl=en
IMPORTANT NOTE: All information presented herewith is provided on an "As Is"
basis, without warranty or the implication thereof. Neither the Quantum Owners Club nor
the individuals associated with the Quantum Owners Club or in the preparation of the
above information shall have any liability to any person or entity with respect to
liability, loss, or damage caused or alleged to be caused directly or indirectly by the
instructions contained within this or related message(s).
