Hi there! I am running a FreeBSD machine with a Oncore UT+ receiver.
At the moment the NTP Oncore driver is hanging here oncore# tail -f /var/log/ntp/clocks 55837 78346.503 127.127.30.0 ONCORE[0]: state = ONCORE_CHECK_CHAN 55837 78350.990 127.127.30.0 ONCORE[0]: Input says chan = -1 55837 78350.990 127.127.30.0 ONCORE[0]: Model # says chan = 8 55837 78350.990 127.127.30.0 ONCORE[0]: Testing says chan = 8 55837 78350.990 127.127.30.0 ONCORE[0]: Using chan = 8 55837 78350.990 127.127.30.0 ONCORE[0]: state = ONCORE_HAVE_CHAN 55837 78352.463 127.127.30.0 ONCORE[0]: state = ONCORE_TEST_SENT 55837 78361.539 127.127.30.0 ONCORE[0]: GPS antenna: OK 55837 78361.540 127.127.30.0 ONCORE[0]: state = ONCORE_INIT 55837 78362.520 127.127.30.0 ONCORE[0]: Oncore: Resend @@Cj 55837 78363.163 127.127.30.0 ONCORE[0]: Setting Posn from input data 55837 78363.164 127.127.30.0 ONCORE[0]: state = ONCORE_ALMANAC 55837 78370.189 127.127.30.0 ONCORE[0]: Posn: 55837 78370.190 127.127.30.0 ONCORE[0]: Lat = N 41.1745292deg, Long = W 8.6560922deg, Alt = 131.84m (432.55ft) GPS 55837 78370.190 127.127.30.0 ONCORE[0]: Lat = N 41deg 10.4718m, Long = W 8deg 39.36553m, Alt = 131.84m ( 432.55ft) GPS 55837 78370.191 127.127.30.0 ONCORE[0]: Lat = N 41deg 10m 28.30s, Long = W 8deg 39m 21.93s, Alt = 131.84m ( 432.55ft) GPS 55837 78370.248 127.127.30.0 ONCORE[0]: Cable delay is set to 25 ns 55837 78370.262 127.127.30.0 ONCORE[0]: Satellite mask angle set to 0 degrees 55837 78372.662 127.127.30.0 ONCORE[0]: Have now loaded an ALMANAC 55837 78372.663 127.127.30.0 ONCORE[0]: state = ONCORE_RUN 55837 78372.663 127.127.30.0 ONCORE[0]: SSstate = ONCORE_SS_DONE 55837 78372.732 127.127.30.0 ONCORE[0]: ONCORE: Detected TRAIM, TRAIM = ON 55837 78372.733 127.127.30.0 ONCORE[0]: Input says TRAIM = 1 55837 78372.733 127.127.30.0 ONCORE[0]: Model # says TRAIM = 1 55837 78372.733 127.127.30.0 ONCORE[0]: Testing says TRAIM = 1 55837 78372.734 127.127.30.0 ONCORE[0]: Using TRAIM = 1 55837 78373.762 127.127.30.0 ONCORE[0]: PPS Offset is set to 0 ns 55837 78373.782 127.127.30.0 ONCORE[0]: Satellite mask angle is 0 degrees After this point nothings happens... yet if I force mode 3 (reset without survey) it works... The problem is that this way I have to wait for an almanac load... too much time. My ntp.oncore.0 file is this MODE 1 # #The following coordinates were surveyed using SynTac over a day # LAT 41 10 28.3055 LONG -8 39 21.9320 HT 131.84 M TRAIM YES DELAY 25 NS CLEAR MASK 0 HARDPPS SHMEM /etc/oncore.0 Can anyone help me? Thanks! Cheers, Miguel _______________________________________________ questions mailing list [email protected] http://lists.ntp.org/listinfo/questions
