We're having problems with the logfile stuff when using radmin.
Here's our radmin.cfg file:
==============begin paste================
AuthPort 1812
AcctPort 1813
DictionaryFile /usr/local/etc/raddb/dictionary
PidFile /var/run/radiusd.pid
Trace 3
LogDir /var/log/radius
LogFile logfile
<ClientListSQL>
DBSource dbi:mysql:radmin:pearl.tseinc.com
DBUsername aaaaaa
DBAuth xxxxxxxx
</ClientListSQL>
<SessionDatabase SQL>
DBSource dbi:mysql:radmin:pearl.tseinc.com
DBUsername aaaaaaa
DBAuth xxxxxxxx
</SessionDatabase>
<Realm DEFAULT>
<AuthBy RADMIN>
DBSource dbi:mysql:radmin:pearl.tseinc.com
DBUsername aaaaaaa
DBAuth xxxxxxxx
# Dont check MAXLOGINS, but do take note of these...
# FRAMED_NETMASK,FRAMED_FILTER_ID,MAXIDLETIME
AuthSelect select PASS_WORD,STATICADDRESS,TIMELEFT,\
NULL,FRAMED_NETMASK,FRAMED_FILTER_ID,\
MAXIDLETIME \
from RADUSERS where \
USERNAME='%n' and BADLOGINS < 5 and \
VALIDFROM < %t and VALIDTO > %t
AuthColumnDef 0,Framed-IP-Netmask,reply
AuthColumnDef 1,Filter-Id,reply
AuthColumnDef 2,Idle-Timeout,reply
AccountingTable RADUSAGE
AcctColumnDef USERNAME,User-Name
AcctColumnDef TIME_STAMP,Timestamp,integer
AcctColumnDef ACCTSTATUSTYPE,Acct-Status-Type,integer
AcctColumnDef ACCTDELAYTIME,Acct-Delay-Time,integer
AcctColumnDef ACCTINPUTOCTETS,Acct-Input-Octets,integer
AcctColumnDef ACCTOUTPUTOCTETS,Acct-Output-Octets,integer
AcctColumnDef ACCTSESSIONID,Acct-Session-Id
AcctColumnDef ACCTSESSIONTIME,Acct-Session-Time,integer
AcctColumnDef ACCTTERMINATECAUSE,Acct-Terminate-Cause,integer
AcctColumnDef FRAMEDIPADDRESS,Framed-IP-Address
AcctColumnDef NASIDENTIFIER,NAS-Identifier
AcctColumnDef NASIDENTIFIER,NAS-IP-Address
AcctColumnDef NASPORT,NAS-Port,integer
AcctColumnDef DNIS,Called-Station-Id
AcctSQLStatement update RADUSERS set
TIMELEFT=TIMELEFT-0%{Acct-Session-Time},
OCTETSINLEFT=OCTETSINLEFT-0%{Acct-Input-Octets},
OCTETSOUTLEFT=OCTETSOUTLEFT-0%{Acct-Output-Octets} where USERNAME='%n'
AddToReply Service-Type = Framed-User, \
Framed-Protocol = PPP,\
Framed-Routing = None,\
Framed-MTU = 1500,\
Framed-Compression = Van-Jacobson-TCP-IP
</AuthBy>
</Realm>
=============end paste==============
Several problems...
1) Even though we have Trace set to 3, radiator is logging lots of level 4
messages (to RADMESSAGES) which are quite annoying and voluminous :) Any way
to tell it that trace 3 means just trace 3 and lower?
2) Radiator set up as above is logging to three places....
/var/log/radius/logfile, /usr/local/etc/raddb/logfile, and the RADMESSAGES
table. Is there any way to tell it to log to RADMESSAGES via SQL ONLY -
nowhere else?
THANKS for any input!
Jay West
===
Archive at http://www.starport.net/~radiator/
Announcements on [EMAIL PROTECTED]
To unsubscribe, email '[EMAIL PROTECTED]' with
'unsubscribe radiator' in the body of the message.
