Bruce:
I just ran (not traced) your code in RB 11.0.3.20611 with v102_roudningTarget
set at 13,437.17 (which is between 10000.00 and 100000.00, and the returned
vale for v102_roundingValue was 25.00. Is this not correct.
Variable = Value
Type------------------ ------------------------------
-------v102_roundingValue = 25.00
CURRENCYv102_roundingTarge = 13,437.17 CURRENCY
Jim
On Sunday, July 26, 2026 at 09:36:29 PM EDT, '[email protected]' via
RBASE-L <[email protected]> wrote:
Hey Buddy thank you.
Without the underscore the same result obtains. All rounding values are applied
within TRACE mode, only the default 50.00 is applied within RUN mode.
Very best, Bruce
------ Original Message ------From "'Buddy Walker' via RBASE-L"
<[email protected]>To [email protected] 7/26/2026 5:26:00
PMSubject Re: [RBASE-L] - IFF statement fail
Bruce
I would suspect the underscore between the 2 and r. When the code is running
maybe it sees the underscore as wild single character and when in trace mode it
isn’t compiling it.
Just a thought
Buddy
Sent from my iPhone
On Jul 26, 2026, at 4:37 PM, '[email protected]' via RBASE-L
<[email protected]> wrote:
All:
RBG11 Current
For charting wide ranges of values, I perform incremental rounding to simplify
display and interpretation (e.g. who cares about $13,437.17 when $13,500 will
do? ).
This is the first time I've attempted to dynamically round with a full-set of
preset increments, using this IFF construct (expanded for clarity ):
{Assign value-range incremental rounding values. } SET VAR v102_roundingValue
= + (IFF('.v102_roundingTarget = 0.00 ', 0.00, +
(IFF('.v102_roundingTarget BETWEEN 0.01 AND 4.99 ', 0.25, +
(IFF('.v102_roundingTarget BETWEEN 5.00 AND 1000.00 ', 5.00, +
(IFF('.v102_roundingTarget BETWEEN 1001.00 AND 10000.00 ', 10.00, +
(IFF('.v102_roundingTarget BETWEEN 10001.00 AND 100000.00 ', 25.00, 50.00 +
)) )) )) )) ))
This works ... sort of. When the routine runs outside of TRACE mode, all
increments except 50.00 are ignored. All v102_roundingTarget values are rounded
by 50.00.
And the kicker is, when I step through the code with F10 in TRACE mode, the
proper increments are applied.
Does anything look out of place here?
Thanks much! Bruce
Bruce A. Chitiea | SafeSectors, Inc.1142 S Diamond Bar Blvd #442Diamond Bar CA
91765-2203
[email protected](909) 238-9012
--
For group guidelines, visit
http://www.rbase.com/support/usersgroup_guidelines.php
---
You received this message because you are subscribed to the Google Groups
"RBASE-L" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion visit
https://groups.google.com/d/msgid/rbase-l/em0a19783d-ef4d-4a17-9087-5bf33046be8d%40safesectors.com.
--
For group guidelines, visit
http://www.rbase.com/support/usersgroup_guidelines.php
---
You received this message because you are subscribed to the Google Groups
"RBASE-L" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion visit
https://groups.google.com/d/msgid/rbase-l/E6F08403-9101-4E10-90F1-3E50FD69C49B%40comcast.net.
--
For group guidelines, visit
http://www.rbase.com/support/usersgroup_guidelines.php
---
You received this message because you are subscribed to the Google Groups
"RBASE-L" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion visit
https://groups.google.com/d/msgid/rbase-l/embeaeb2c1-e079-4d76-8ff6-3258ac55646d%40safesectors.com.
--
For group guidelines, visit
http://www.rbase.com/support/usersgroup_guidelines.php
---
You received this message because you are subscribed to the Google Groups
"RBASE-L" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion visit
https://groups.google.com/d/msgid/rbase-l/1954032594.2473319.1785117967852%40mail.yahoo.com.
