"and (just noticed) 3 x 6 in the Flickr pages?" My RoadUno is 2x7. It's the stock 38/26 in front, and 12-28 in back
"I'm probably going to use a 2spd kick back hub (yes, they are heavy....) with a 3 ring set up." How will that work? If you run a 3-ring setup with a front derailleur you'll need a tensioner of some kind. If you run a 2 speed kickback hub you'll need to NOT run a tensioner of any kind. Will it be a 2-speed kickback setup with no tensioner, and you can manually move the wheel to accommodate one of the three rings? If you do that, then you need new rear brake setup for each wheel position. Will it be front brake only? Have fun with it, whatever you do. Bill Lindsay El Cerrito, CA On Thursday, August 22, 2024 at 3:16:11 PM UTC-7 [email protected] wrote: > I've got an Ana Purple RoadUno showing up tomorrow, Friday. (first bike > purchase from Rivendell...) > I'm temporarily on weight lifting restrictions (thanks, cataract!), so > I've recruited my son to lend me a hand. Maybe I lend him a beer or > something... > > As far as going fixed, I saw that the RoadUno page (one of them, can't > recall which) recommends against doing so, as the bottom bracket drop is > relatively low (80mm drop?) . > > Thanks for the early build pics and tips. -- and (just noticed) 3 x 6 in > the Flickr pages? I'm probably going to use a 2spd kick back hub (yes, > they are heavy....) with a 3 ring set up. > Cheers. > > On Thursday, August 22, 2024 at 11:50:21 AM UTC-4 Bill Lindsay wrote: > >> Keith >> >> What exactly are you after? Are you looking to build a Roaduno fixed >> with zero brakes and need to know max fenderless tire size you can run on >> your fixie? Are you plotting a cantilever conversion on a Roaduno? Do you >> have a particular tire size that you must have, or is it just you need to >> know the absolute largest tire that will fit without fenders. Have you >> asked Rivendell to do these measurements for you? If you are in market to >> buy a frame and since they have lots of frames, maybe that's their job? >> >> I will be taking some Garage Door photos for Will, so he can put my build >> in the Riv email newsletter. At that time, I'll try to capture what you >> may be after. >> >> Bill Lindsay >> El Cerrito, CA >> >> On Wednesday, August 21, 2024 at 11:03:50 AM UTC-7 iamkeith wrote: >> >>> Beautiful, Bill. I suspect you'll be responsible for a number of new >>> Roaduno sales in the near future, as people see your bike. >>> >>> When you have time, would you mind sharing some close-up pictures of >>> tire clearances at the chain stays, seat stay brake bridge bridge and fork >>> crown areas? You build too quickly. What I've really been dying to know >>> is how big of a tire can be fit WITHOUT caliper brakes installed. (I've >>> been half-heartedly toying with a couple of alternative brake ideas since >>> the Roaduno project shifted from a canti-clem to a caliper-homer format.) >>> I dont expect you to disassmle or try different tires but, for anyone else >>> reading this and getting ready to start their own build, I'd appreciate any >>> insights if it's convenient. >>> >>> On Wednesday, August 21, 2024 at 9:32:35 AM UTC-6 Bill Lindsay wrote: >>> >>>> Good initial instruction, good tools, and lots of practice. That's my >>>> formula for developing that confidence and mechanics' instinct. I think >>>> most procedures really sink in after you fail one or more times, but >>>> failing at this operation on a new frame would be a bummer. If you are >>>> nervous, have a pro do it. If you want the practice, find a pro that will >>>> oversee you doing it. >>>> >>>> BL in EC >>>> >>>> >>>> On Wednesday, August 21, 2024 at 8:12:56 AM UTC-7 Michael Connors wrote: >>>> >>>>> Hi Bill. I am nervous about running a tap in the RD hanger. How do >>>>> you make sure that you are in the existing thread and not cutting a new >>>>> one? >>>>> >>>>> >>>>> >>>>> Thread chasing was necessary on the RD hanger, but it was aligned >>>>> perfectly. Most but not all of the H2O bolt and fender bolt bosses were >>>>> already chased. It was all straightforward prep for a mechanic. There >>>>> was >>>>> no BB cable guide included, but I had those on-hand. I installed a >>>>> Shimano >>>>> CX70 front der and a White Industries DOS ENO 16/19 freewheel. I >>>>> installed >>>>> a Suntour Sprint down tube shifter on the shifter boss, with my own >>>>> custom >>>>> machined stop that causes it to sit proud of the down tube in the >>>>> small-ring position. >>>>> >>>>> With the faceplater stem pretty much slammed, and the saddle at my >>>>> height, I'm happy at the silhouette of the bike. I'm eager to get a >>>>> chain >>>>> on it and start riding it. >>>>> >>>>> Have a look: >>>>> https://flickr.com/photos/45758191@N04/albums/72177720319657823 >>>>> >>>>> Bill Lindsay >>>>> El Cerrito, CA >>>>> >>>>> -- You received this message because you are subscribed to the Google Groups "RBW Owners Bunch" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/rbw-owners-bunch/234a3d08-ce97-47a8-a91c-28cbba635447n%40googlegroups.com.
