Ok, I looked up the bars. Classic road shape so I'm sure you're mounting road levers. In my experience road levers always take some twisty action to get in place on the curve. A little grease or chain lube will help, but I wouldn't fret too much about light scratching. You obviously don't want deep gouges in aluminum, but a little surface scratching won't hurt anything, and it'll be covered by bar tape. Speaking of gouges, don't screw the levers down so tight that they dig into the bar. I made this mistake many times in my early days. I never had a problem, but it wasn't necessary. Get 'em snug, then wrap the bars. Everything will stay in place. This goes for the front derailer, too. It doesn't need to be jammed into the seattube. Snug is good. Let's see, what else? Bottom bracket. Pay attention to the threading, get the "long end" in first, snug it up to the shell hand tight. Do NOT use the BB tool to tighten. Now install the fixed cup on the other side with the tool. Tightening the fixed cup tightens the whole thing. I don't understand the physics of it, but that's how www.parktool.com says to do it. It works. Joe Bernard
On Tuesday, September 4, 2012 1:59:01 PM UTC-7, Joe Bernard wrote: > My general rule is start from the bottom and move up. Wheels, cranks/bb, > derailers, brakes, then the cockpit. I try to save the handlebars for last > to avoid errant swings into the toptube while I'm busy with other things, > but this may not be an issue for you if you're using a proper repair stand. > I don't have one. > > A little grease to help the levers along is ok, IMO. You'll be able to get > 'em good and tight once in place. I'd double check the specs for bar and > levers first, though. You may be trying to fit MTB-spec levers on a > road-spec bar. > > Joe Bernard > Vallejo, CA. > > On Monday, September 3, 2012 10:29:40 PM UTC-7, Michael Richters wrote: > >> I'm about to embark on the adventure of putting together a bicycle for >> the first time, and I find myself anticipating all manner of >> difficulties arising from my lack of experience. I've got my >> brand-new A Homer Hilsen and a large assortment of parts, doo-dads, >> and associated accoutrements, and even most -- if not all -- of the >> tools that I ought to need to put it all together, but before I begin, >> I'd like to solicit some advice from the learned audience of this >> mailing list. >> >> My first dilemma is where to begin. Clearly, I have a few choices, >> but it's not clear what unforseen surprises await me if I do things in >> an order that it less than optimal. The only thing attached to the >> frame so far is the headset (and front fork, of course). Perhaps the >> best thing to start with would be the bottom bracket, then the cranks? >> Or maybe there's a good reason to set up the stem and handlebar >> first? Speaking of which, it seems nigh-impossible to get the brake >> levers I've got onto the bar. If watched this video >> (http://youtu.be/oEUm3VzF_Z0), but it seems the bar that I've chosen >> (Grand Bois Randonneur) might have a larger diameter in the bend, >> because even with the clamp loosened all the way (or, indeed, >> separated completely from the brake levers), it's a very tight fit, >> and it seems impossible to slide onto the bar without causing lots of >> zig-zag scratches in the aluminum bar. >> >> This brings me to another, more general question -- where and how much >> grease to use. It doesn't seem like a great idea to grease the >> aforementioned brake lever clamps, but maybe that's the only way to >> get them in place. My inclination is to grease just about everything, >> especially threads, but maybe there are a few places where lubrication >> is a particularly bad idea, and everyone is just assumed to know about >> it... >> >> Here's hoping I don't destroy anything in this process; I'd rather >> learn from the mistakes of others than by making my own, at least in >> this case. >> >> --MR >> > -- You received this message because you are subscribed to the Google Groups "RBW Owners Bunch" group. To view this discussion on the web visit https://groups.google.com/d/msg/rbw-owners-bunch/-/Ws6vww6tIrEJ. To post to this group, send email to [email protected]. To unsubscribe from this group, send email to [email protected]. For more options, visit this group at http://groups.google.com/group/rbw-owners-bunch?hl=en.
