Re: [RE-wrenches] Trojan RE Series Tech question

[Allan Sindelar]

Dave, My response is only part of the answer, but may help with your system setup. Both the SB50 and the FM60 have the ability to limit the absorption time, although by different methods. This may serve as a key setting to reduce gassing and water use when the homeowners are away. With the SB50, you can adjust the float transition current to a allow the switch the batteries from acceptance (Blue Sky's term for absorption) into float sooner. The default recommendation is 2% of battery capacity per the manual; perhaps 3% would allow it to transition sooner. The FM60 has a setting to allow transition to float at a set current - that is, as long as the voltage is at the bulk/absorption setpoint (suggesting that the batteries are nearly full), rather than staying in absorption for the entire timed absorption period, if the current necessary to maintain absorption voltage drops below this threshold (of typically around 2% of battery capacity, or about 44 amps in your case) the controller will go into float. My understanding is that this is specifically to reduce daily absorption time when batteries are lightly cycled, as in this case. What I don't know is how these two very different controllers (digital vs. analog, among other differences) will work as a team together. Other Wrenches may have more experience. My idea is to set the FTC on the SB50 high so that it will transition first, allowing the FM80 to regulate final transition. Maybe instead set the SB50 to a slightly lower bulk/acceptance setpoint voltage, so that the SB50 drops out a bit sooner and the FM80 completes the daily charge. Allan Allan Sindelar al...@positiveenergysolar.com NABCEP Certified Photovoltaic Installer NABCEP Certified Technical Sales Professional New Mexico EE98J Journeyman Electrician Positive Energy, Inc. 3201 Calle Marie Santa Fe, New Mexico 87507 505 424-1112 www.positiveenergysolar.com On 8/2/2011 3:49 PM, Dave Palumbo wrote: Our go to guy at Trojan, Ron Parades, is evidently gone. That’s what they said at his old phone extension at Trojan. I left a message for tech support there and have not heard back as of yet.   Is there another Trojan Tech person to  specifically ask for now? And is there one on this list helping out as Ron did previously?   I have a question on the Trojan RE Series charging voltage settings. I know the specific gravity is lower on this series and the bulk charge voltage is correspondingly lower than the old L-16’s.   I have an off grid system for a remote home where the client is only there from June through October. He has 1,560 Watts of solar and a new battery bank rated at 2,220 AH at 12 volts (12 L-16 RE-2V batteries). That is a charge rate in the C/20 range. The homeowner uses the system reasonable hard when they are there but during the winter the load is only 15AH per day for a low voltage security system.   He has previously serviced his Rolls CH-375’s (1,400AH with 450 Watts of PV on that system, about a C/33 rate) in October before leaving for 7 months and has not had a problem with the battery electrolyte boiling off too much over that time period. He got 10 years out of the Rolls batteries using it in this way. The charge voltage for that system was 14.6  through a Solar Boost 50.   The new system will have 1,110 Watts charging through a Out Back FM 80 alongside the original array on the Solar Boost for the total of 1,560 Watts of PV.   I am thinking of charging at 14.6 Bulk with a two hour absorption time period in the summer  and then changing it for the 7 month period when the system is lightly used.   My question is, how low should I set the two charge controllers for winter/spring use to minimize water consumption? I’m thinking of 14.2 or 14.3 Volts, with a reduced absorption time of one hour. And what should the float voltage setting be? The batteries are in a basement that is kept at about 55 degrees. There is temperature compensation on the battery charging.   Thank you,   David Palumbo Independent Power LLC 462 Solar Way Drive Hyde Park, VT 05655 www.independentpowerllc.com NABCEP Certified PV Installer Vermont Solar Partner 23 Years Experience, (802) 888-7194   _______________________________________________ List sponsored by Home Power magazine List Address: RE-wrenches@lists.re-wrenches.org Options & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org List rules & etiquette: www.re-wrenches.org/etiquette.htm Check out participant bios: www.members.re-wrenches.org

_______________________________________________
List sponsored by Home Power magazine

List Address: RE-wrenches@lists.re-wrenches.org

Options & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org

List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org

List rules & etiquette:
www.re-wrenches.org/etiquette.htm

Check out participant bios:
www.members.re-wrenches.org