to further complicate things, i have seen "regulator oscillation" problems with
2 in series.
todd
On Monday, February 17, 2014 2:30pm, "Ray Walters" <[email protected]> said:
Alot of these generator setups need 2 regulators, so usually the regular
one stays at the tank, size the pipe for the flow rate ( just like wire
and amps.... ;-) .) and put the 2nd regulator right at the generator.
R.Ray WaltersCTO, Solarray, IncNabcep Certified PV Installer, Licensed Master
ElectricianSolar Design Engineer303 505-8760On 2/17/2014 3:17 PM, Larry
Crutcher, Starlight Solar Power Systems wrote:Ditto Tom, seen this too
often in Mexico. I carry a manometer to make check the pressure at the LP
input to the generator with the engine running. Make sure it is
at/above 11" WC when it starts to act up. If the regulator is at the
tank, long vapor runs can cause too much pressure loss.
Larry
On Feb 17, 2014, at 1:36 PM, Tom Duffy <[mailto:[email protected]]
[email protected]> wrote:
Hi Guys
We have had “icing” problems here in Central America as
well where the gas company put in ½’ pipe to a 12K
Gillette Generator, same description the gen would
initially start and run fine but then it went erratic the
Radian didn’t like it, the customer wanted to blame the
Radian (I was sure it wasn’t)
The installer/dealer couldn’t figure it out. I went out
and immediately saw the small pipe, plus they had
bent a crimp into the incoming fuel line as well. ¾”
line fixed the whole thing. LP has a lot of moisture and
will always have delivery problems with funky installation
of pipe. Seems that a lot of gas guys just hook up kitchen
ranges (Here)
Kind regards
Tom Duffy
Senior Solar Design Engineer
<image002.png>
E-Mail: [mailto:[email protected]] [email protected]
Panama Office: 507-6126-1253
Direct Toll Free: 888-503-6772
International: 575-539-2111
SKYPE Address: thesolarbiz
Although no trees were killed in the sending of this
message, a large number of electrons were terribly
inconvenienced.
Confidentiality Notice: This message including any
attachments is for the sole use of the intended recipient
and may contain confidential and privileged information.
Any unauthorized review, use, disclosure or
distribution is prohibited. If you are not the
intended recipient, please contact the sender and delete
any copies of this message.
_______________________________________________List sponsored by Home Power
magazineList Address: [mailto:[email protected]]
[email protected] email address &
settings:[http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org]
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.orgList-Archive:
[http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org]
http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.orgList rules &
etiquette:[http://www.re-wrenches.org/etiquette.htm]
www.re-wrenches.org/etiquette.htmCheck out participant
bios:[http://www.members.re-wrenches.org] www.members.re-wrenches.org
Sent from Finest Planet WebMail.
_______________________________________________
List sponsored by Home Power magazine
List Address: [email protected]
Change email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
List rules & etiquette:
www.re-wrenches.org/etiquette.htm
Check out participant bios:
www.members.re-wrenches.org
