Brian, I have used the SnapNRack and i do like their clips more than the J-hooks.
Thanks *Benn Kilburn * CSA Certified Solar Photovoltaic Systems Electrician, SkyFire Energy Inc 14515 – 121A Ave NW | Edmonton, AB | T5L 2T2 P: 780-474-8992 | F: 888-405-5843 www.skyfireenergy.com [image: email] <b...@skyfireenergy.com> [image: facebook] <https://www.facebook.com/SkyFireEnergy> [image: twitter] <https://twitter.com/SkyFireEnergy> [image: linkedin] <https://www.linkedin.com/company/283735?trk=tyah&trkInfo=tarId%3A1408655033432%2Ctas%3Askyfire%2Cidx%3A2-2-5> [image: SkyFire Energy Logo_horizontal] On Wed, Jun 21, 2017 at 11:42 AM, Brian Teitelbaum <bteitelb...@aeesolar.com > wrote: > Benn, > > > > You might want to take a look at the SnapNrack Array Edge Screen system > > > > It’s universal since it attaches to the module frames, not the racking. > Looks pretty nice too. > > > > Brian Teitelbaum > > AEE Solar > > > > *From:* RE-wrenches [mailto:re-wrenches-boun...@lists.re-wrenches.org] *On > Behalf Of *Benn Kilburn > *Sent:* Wednesday, June 21, 2017 10:07 AM > *To:* RE-wrenches > *Subject:* Re: [RE-wrenches] Rodent/Pigeon/Critter Guards > > > > I'm hoping to get some feedback on this topic, as there was none when I > posted it back in 2015. > > > > Our region is seeing more and more problems with pigeons nesting under PV > arrays, mostly on new homes in newly developed areas of the city. > > We have been called to some sites that had particularly bad problems with > pigeons nesting and pigeon poop covering the roof itself (surprisingly more > so that the array, unless it is just the rain washing it off the modules > easier than the roof?) and the eavestroughs filled with poop and > overflowing onto the ground. > > > > We really want to nip this issue in the butt since none of us want people > associating PV systems with pigeon problems. We have heard that some of > these problem houses have a neighbourhood reputation as "the pigeon house". > > > > Has anyone tried and had success with any of the solutions "other than" > the wire mesh and J-hooks??? I'm not confidant that the j-hooks are robust > enough to last very long. We often have several on each install that the > washer simply will not hold tight. > > (See the prior post below for some other suggestions) > > > > Thanks! > > Benn > > SkyFire Energy > > > On Jul 22, 2015, at 2:00 PM, Benn Kilburn <b...@skyfireenergy.com> wrote: > > Wrenches, > > I've looked and found a few older threads on the topic but thought it is a > good time to refresh our collective info on this as we are getting more > requests to install these (and it is also going to be required by code on > some systems when our province adopts the 2015 Canadian Electrical Code. > We currently use the 2012 code) > > The issue that we are directly addressing is mostly pigeons hanging > out/nesting under rooftop arrays, for now. I haven't heard of any specific > rodent issues in our region. > > I have installed the SnapNRack Edge Screen. This was on a concrete tile > roof so the problem i saw with that was the screen did not contour the > tile, leaving a small gap where one tile overlaps the one below it, roughly > 25mm (1"). This would not be an issue with keeping out pigeons, but i > could imagine that a persistent rodent could squeeze its way thru the small > gap. This would not be an issue on the more common asphalt shingle roofs > and i would say it is a solid product. > > The products i'm aware of are: > > SnapNRack > > Kinetic > > Heyco > > spiffysolar > solatrim.com > > Kinetic, Heyco, and Spiffy each seem to be basically the same; wire mesh > and a j-hook that attaches to the module frame. > > SnapNRack is wire mesh but attaches with a more more robust clip that also > provides more vertical support to the mesh. (It was suggested that rodents > may be able to push under the mesh when its only supported at the top with > j-hooks) > > I've seen the wire mesh installed so that it comes down only as far as the > roof, so the height of the mesh is essentially the height from the top of > the mod frame to the roof surface, but i have also seen it where the mesh > is taller than this and the excess (rather than being trimmed to size) > comes down and lays out on the roof in an outward direction. It was > suggested that this may be more of a deterrent to rodents that would > otherwise push their way under the mesh if it only comes down to meet the > roof. > > Comments/Suggestions? > > > > The last product mentioned, solatrim, is completely different from the > rest. It looks much more solid that the rest and uses a peel-and-stick > approach using a 3M adhesive tape. My first and only initial apprehension > with this one is the adhesive. While 3M makes darn good adhesives, it > leaves to question how it will hold up against our seasonal ambient > temperature swings of above +30degC to below -40degC. Their spec sheet > states it is good btwn -34.4degC to 149degC. So for me to even try it would > not be within the mfgr's specs :( > > What products have you used? What did you like/dislike about them? > > Cheers, > > *Benn Kilburn * > > CSA Certified Solar Photovoltaic Systems Electrician, SkyFire Energy Inc > > 6706 – 82 Ave NW | Edmonton, AB | T6B 0E7 > > P: 780-474-8992 <(780)%20474-8992> | F: 888-405-5843 <(888)%20405-5843> | > www.skyfireenergy.com > > [image: email] <b...@skyfireenergy.com> [image: facebook] > <https://www.facebook.com/SkyFireEnergy> [image: twitter] > <https://twitter.com/SkyFireEnergy> [image: linkedin] > <https://www.linkedin.com/company/283735?trk=tyah&trkInfo=tarId%3A1408655033432%2Ctas%3Askyfire%2Cidx%3A2-2-5> > [image: google] <https://plus.google.com/+SkyFireEnergy/> > > [image: SkyFire Energy Logo_horizontal] > > > _______________________________________________ > List sponsored by Redwood Alliance > > List Address: RE-wrenches@lists.re-wrenches.org > > Change listserver email address & settings: > http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org > > List-Archive: http://www.mail-archive.com/re-wrenches@lists.re-wrenches. > org/maillist.html > > List rules & etiquette: > www.re-wrenches.org/etiquette.htm > > Check out or update participant bios: > www.members.re-wrenches.org > > >
_______________________________________________ List sponsored by Redwood Alliance List Address: RE-wrenches@lists.re-wrenches.org Change listserver email address & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org List-Archive: http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html List rules & etiquette: www.re-wrenches.org/etiquette.htm Check out or update participant bios: www.members.re-wrenches.org