Kirk,
I think you'll probably have to use a stainless cable tie going all the
way around the rail. The hanger clips you inquired about would probably
be a poor choice on the sloped rails anyway. Another possibility,
admittedly most costly and labor intensive, is to use something similar
to these vinyl cushioned cable clamps
<https://www.fastenal.com/products/details/0762883> that could be held
with 3/4" tee bolts. I believe that the tee bolts are Sunmodo part
B20015-004, it's not a catalog item but you can order them.
Kent Osterberg
Blue Mountain Solar
www.bluemountainsolar.com
On 9/7/2020 10:41 AM, Kirk Herander, VSE wrote:
Thanks,
Unfortunately the HR300 rail which I'm using has no side channels,
just 1/4" top and 3/8" bottom ones.
*Kirk Herander / **kirkh@vermont.solar <mailto:kirkh@vermont.solar>*
*Owner|Principal, VT Solar, LLC*
*/Celebrating our 29^th Anniversary 1991-2020/*
*www.vermont.solar*
<https://nam02.safelinks.protection.outlook.com/?url=www.vermontsolarnow.com&data=02%7C01%7C%7C9f0330d75a244870112408d685311841%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636842843233477645&sdata=0NjyuKeQbEK6245SNnk8X4XnP9Q%2B%2BqtvcALkdDghvk4%3D&reserved=0>**
dba Vermont Solar Engineering
802.863.1202
On 9/7/2020 12:55:30 PM, Kent Osterberg <k...@coveoregon.com> wrote:
Kirk,
For the HR150 rail, Sunmodo has a channel clip, part A20252-001 or
A20252-BK1 (black), that will hold the wires in the channel on the
side of the rail. I don't see it in their recent catalog, but I have
purchased them recently.
For the heavier rails, which are probably being used on the ground
mount, there is a cable clip designed to attach to the 3/8" bolt
slot, part A20162-001, unfortunately it was sized for the older
Enphase cable and isn't much use for anything else.
Stainless cable ties ...
Kent Osterberg
Blue Mountain Solar
70177 Ponderosa Ln.
Cove, OR 97824
www.bluemountainsolar.com
On 9/7/2020 5:44 AM, Kirk Herander, VSE wrote:
All,
I am installing a Sunmondo ground mount for for first time. They
don't offer a wire clip to work on their rail. One which clips in
the top channel and hangs off the side, that is. The top channel
accommodates a 1/4-20 screw, but the rail is wider than any I've
used before, thus i can't find a clip to span the channel to rail
side and snap in.
Looked at Heyco and Hellermantyton lines but no luck. Any ideas?
*Kirk Herander / **kirkh@vermont.solar <mailto:kirkh@vermont.solar>*
*Owner|Principal, VT Solar, LLC*
*/Celebrating our 29^th Anniversary 1991-2020/*
*www.vermont.solar*
<https://nam02.safelinks.protection.outlook.com/?url=www.vermontsolarnow.com&data=02%7C01%7C%7C9f0330d75a244870112408d685311841%7C84df9e7fe9f640afb435aaaaaaaaaaaa%7C1%7C0%7C636842843233477645&sdata=0NjyuKeQbEK6245SNnk8X4XnP9Q%2B%2BqtvcALkdDghvk4%3D&reserved=0>**
dba Vermont Solar Engineering
802.863.1202
_______________________________________________
List sponsored by Redwood Alliance
List Address: RE-wrenches@lists.re-wrenches.org
Change listserver email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
List rules & etiquette:
www.re-wrenches.org/etiquette.htm
Check out or update participant bios:
www.members.re-wrenches.org
