Hi Jamie - the mods you included the spec sheet for are “E” series micros which are in fact Enphase IQ7 micros. The Mods that Jason has are older, with d series micros according to the part number he posted. SunPower monitoring can be switched over to Enphase for a fee as long as the mods include Enphase micros.
It’s interesting to hear about the potential conflict with mid clamps and Enphase invisimount clamps. As far as I know, we have used IronRidge with SunPower InvisiMount frames many times with no issues. The IronRidge XR rail manual specifies that they are compatible, see page 28: https://files.ironridge.com/pitched-roof-mounting/resources/brochures/IronRidge_Flush_Mount_Installation_Manual.pdf Best, August On Fri, Feb 21, 2025 at 6:30 AM Jamie Elmlinger via RE-wrenches < [email protected]> wrote: > Hey Jason, > I think I can confirm a couple of things, but I'll include the spec sheet > for you as well. > That micro is just a white labeled Enphase. Believe it or not they are > still being installed today. > So if it's the same module I think it is, you can install them just like > normal. However, the tricky part is module thickness, you can't use the > new Ironridge stopper sleeve and you have to find the matching stopper > sleeve to go with a UFO that supply has dwindled on. I haven't found any > other mids and ends to accommodate. I know Pegasus is working on it. > Hope this helps. > > On Fri, Feb 21, 2025 at 9:11 AM Jason Szumlanski via RE-wrenches < > [email protected]> wrote: > >> I was contacted by a homeowner with a bunch of spr-x21-350-blk-d-ac that >> were removed for roof replacement right around the time that SunPower went >> bankrupt. All the cabling is missing, and I'm not sure if the monitoring >> system is even viable anymore. >> >> Any suggestions for how to handle this? I think the IQ8X microinverter >> might be compatible and the DC leads from the panel might be long enough if >> I frame mount the microinverter or carefully position microinverters on the >> rail. >> >> The other issue I have is all of the proprietary clamps for these panels >> are missing. Can these panels be top clamped with standard UFO or other mid >> clamps? >> >> I have been helping quite a few people get systems with SunPower branded >> Enphase microinverters converted over to the Enlighten monitoring portal, >> but I am not familiar with the microinverters on the spr-x21-350-blk-d-ac. >> >> Jason Szumlanski >> Florida Solar Design Group >> _______________________________________________ >> List sponsored by Redwood Alliance >> >> Pay optional member dues here: http://re-wrenches.org >> >> List Address: [email protected] >> >> Change listserver email address & settings: >> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org >> >> There are two list archives for searching. When one doesn't work, try the >> other: >> https://www.mail-archive.com/[email protected]/ >> http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org >> >> List rules & etiquette: >> http://www.re-wrenches.org/etiquette.htm >> >> Check out or update participant bios: >> http://www.members.re-wrenches.org >> >> _______________________________________________ > List sponsored by Redwood Alliance > > Pay optional member dues here: http://re-wrenches.org > > List Address: [email protected] > > Change listserver email address & settings: > http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org > > There are two list archives for searching. When one doesn't work, try the > other: > https://www.mail-archive.com/[email protected]/ > http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org > > List rules & etiquette: > http://www.re-wrenches.org/etiquette.htm > > Check out or update participant bios: > http://www.members.re-wrenches.org > >
_______________________________________________ List sponsored by Redwood Alliance Pay optional member dues here: http://re-wrenches.org List Address: [email protected] Change listserver email address & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org There are two list archives for searching. When one doesn't work, try the other: https://www.mail-archive.com/[email protected]/ http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org List rules & etiquette: http://www.re-wrenches.org/etiquette.htm Check out or update participant bios: http://www.members.re-wrenches.org
