Hello all,
I'm trying to boot a kernel compiled from the soruce RPM of the RH
Advanced Server 2.1, but it always fail to load the modules from the
initrd image.
I built the rpm from source, after compiling and installing the packages
needed to satisfy the (pre)requirements of the kernel spec file.
And if I boot using ext2 fs only so that no modules is needed all goes
well, and when I load the ext3 module it works.
Any ideas? The boot log is attached.
--
Andrea Dell'Amico - <mailto:[EMAIL PROTECTED]>
Sendmail may be safely run set-user-id to root.
-- Eric Allman, "Sendmail Installation Guide"
root (hd0,0)
Filesystem type is ext2fs, partition type 0x83
kernel /vmlinuz-2.4.9-e.10.petra ro root=/dev/hda2 console=tty0 console=ttyS1
[Linux-bzImage, setup=0x1400, size=0xf250a]
initrd /initrd-2.4.9-e.10.petra.img
[Linux-initrd @ 0x7ed3000, 0x1c729 bytes]
Linux version 2.4.9-e.10.petra (root@petra72f) (gcc version 2.96 20000731 (Red Hat
Linux 7.2 2.96-108.1)) #1 Tue Dec 10 15:05:24 EST 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
BIOS-e820: 000000000009f400 - 000000000009f800 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007f00000 (usable)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
Scanning bios EBDA for MXT signature
0MB HIGHMEM available.
127MB LOWMEM available.
On node 0 totalpages: 32512
zone(0): 4096 pages.
zone(1): 28416 pages.
zone(2): 0 pages.
Kernel command line: ro root=/dev/hda2 console=tty0 console=ttyS1
Initializing CPU#0
Detected 1101.971 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2195.45 BogoMIPS
Memory: 123916k/130048k available (1806k kernel code, 4852k reserved, 97k data,
224k init, 0k highmem)
Dentry-cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode-cache hash table entries: 8192 (order: 4, 65536 bytes)
Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 32768 (order: 6, 262144 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel(R) Celeron(TM) CPU 1100MHz stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfdba1, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Using IRQ router PIIX [8086/2440] at 00:1f.0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.14)
mxt_scan_bios: enter
Starting kswapd v1.8
bigpage subsystem: allocated 0 bigpages (=0MB).
VFS: Diskquotas version dquot_6.5.0 initialized
aio_setup: num_physpages = 8128
aio_setup: sizeof(struct page) = 68
Detected PS/2 Mouse Port.
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ
SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
block: queued sectors max/low 82242kB/27414kB, 256 slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz PCI bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev f9
PIIX4: chipset revision 17
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
hda: Maxtor 2B020H1, ATA DISK drive
hdc: Maxtor 2B020H1, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
blk: queue c03687a0, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c03687a0, I/O limit 4095Mb (mask 0xffffffff)
hda: 40020624 sectors (20491 MB) w/2048KiB Cache, CHS=2491/255/63, UDMA(100)
blk: queue c0368ae4, I/O limit 4095Mb (mask 0xffffffff)
blk: queue c0368ae4, I/O limit 4095Mb (mask 0xffffffff)
hdc: 40020624 sectors (20491 MB) w/2048KiB Cache, CHS=39703/16/63, UDMA(100)
Partition check:
hda: hda1 hda2 hda3
hdc: hdc1
floppy0: no floppy controllers found
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 113k freed
VFS: Mounted root (ext2 filesystem).
Red Hat nash version 3.2.6 starting
Loading jbd module
ERROR: /bin/insmod exited abnormally!
Loading ext3 module
ERROR: /bin/insmod exited abnormally!
Mounting /proc filesystem
Creating root device
Mounting root filesystem
mount: error 19 mounting ext3
pivotroot: pivot_root(/sysroot,/sysroot/initrd) failed: 2
Freeing unused kernel memory: 224k freed
Kernel panic: No init found. Try passing init= option to kernel.
