This is for the guys that follow:  

situation: software raid 1 (sda and sdb )and lvm setup during install. 
no problems once I made a separate raid partition for a non LVM /

Then, since I had no prior experience with software raid and the box is
headed to wisconsin for a client.  I thought "Hey I wonder what happens
when you pull on of these hot swap drives out of this HP netserver?"

so I pulled sda out.  box still ran. cool.

then I dug around for way more time than I care to admit, looking for
how to run raidhotadd to get it back.  of course it would not boot from
sdb either with or without the first drive installed.  After some
considerable dinking and booting from a floppy, (Thanks be to all the
higher powers everywhere I made that floppy) I managed to wipe the
partition table from the drive.  Not sure how. I got the partition table
back using fdisk but still coul bot get the frigging thing to add the
drive to the array.  I could see via cat /proc/mdstats that sda was
still unused.

I found references to the following syntax:

raidhotadd /dev/md0 /dev/sda

seemed to work but then no way to add md1

BTW now that I think about it this is probably where the partition table
got hosed.

the correct incantation is obvious now 

raidhotadd /dev/md0 /dev/sda1
raidhotadd /dev/md1 /dev/sda2
 
FWIW raidhotadd returns pretty quick but there is still stuff
happening.  I could watch the progress of the rebuild process by
repeated cat /proc/mdstats.  Actually gives a pretty nice estimate of
the time remaining for the process to complete.

"Cool" I says to myself.  finally figured it out.  reboot and ... nada
*&%^# (* % ^&(*$#^ [EMAIL PROTECTED] (*^#$^ (That part was out loud)

anyway at least I am not the only poor sap that has tried to figure out
how to get grub to write itself to a raid1 drive since I read so many
google hits and maillist postings that talked of the problem.

The solution was to NOT use frigging grub-install although now that I
did it from the grub command line I might could make it work.

what I did was this:

grub> device (hd0) /dev/sda
grub> root (hd0,0)
 Filesystem type is ext2fs, partition type 0xfd
grub> setup (hd0)

the setup command spit out a lot of stuff that looked good and after
quitting out of grub and rebooting I am now booting off the hard drive
again.

BTW I found this nugget at:

http://mail.gnu.org/archive/html/bug-grub/2002-11/msg00005.html

If I had not spent all damn day dinking with this I would probably try
it again after doing the grub thing on sdb and seeing if it would boot
from that drive too but I be tired.

I hope this helps someone in the future.

Bret 


here is the environment.

[EMAIL PROTECTED] root]# fdisk -l /dev/sda

Disk /dev/sda: 18.2 GB, 18210037760 bytes
64 heads, 32 sectors/track, 17366 cylinders
Units = cylinders of 2048 * 512 = 1048576 bytes

   Device Boot    Start       End    Blocks   Id  System
/dev/sda1   *         1       500    511984   fd  Linux raid autodetect
/dev/sda2           501     17366  17270784   fd  Linux raid autodetect
[EMAIL PROTECTED] root]# fdisk -l /dev/sdb

Disk /dev/sdb: 18.2 GB, 18210037760 bytes
64 heads, 32 sectors/track, 17366 cylinders
Units = cylinders of 2048 * 512 = 1048576 bytes

   Device Boot    Start       End    Blocks   Id  System
/dev/sdb1   *         1       500    511984   fd  Linux raid autodetect
/dev/sdb2           501     17366  17270784   fd  Linux raid autodetect

[EMAIL PROTECTED] root]# cat /etc/fstab
/dev/md0                /                       ext3    defaults        1 1
none                    /dev/pts                devpts  gid=5,mode=620  0 0
/dev/Volume00/LogVol00  /home                   ext3    defaults        1 2
none                    /proc                   proc    defaults        0 0
none                    /dev/shm                tmpfs   defaults        0 0
/dev/Volume00/LogVol02  /tmp                    ext3    defaults        1 2
/dev/Volume00/LogVol01  /usr                    ext3    defaults        1 2
/dev/Volume00/LogVol04  /usr/local              ext3    defaults        1 2
/dev/Volume00/LogVol03  /var                    ext3    defaults        1 2
/dev/Volume00/LogVol05  swap                    swap    defaults        0 0
/dev/cdrom              /mnt/cdrom              udf,iso9660 noauto,owner,kudzu,ro 0 0
/dev/fd0                /mnt/floppy             auto    noauto,owner,kudzu 0 0


[EMAIL PROTECTED] root]# cat /etc/raidtab 
raiddev             /dev/md1
raid-level                  1
nr-raid-disks               2
chunk-size                  64k
persistent-superblock       1
nr-spare-disks              0
    device          /dev/sda2
    raid-disk     0
    device          /dev/sdb2
    raid-disk     1
raiddev             /dev/md0
raid-level                  1
nr-raid-disks               2
chunk-size                  64k
persistent-superblock       1
nr-spare-disks              0
    device          /dev/sda1
    raid-disk     0
    device          /dev/sdb1
    raid-disk     1

[EMAIL PROTECTED] root]# cat /boot/grub/grub.conf 
# grub.conf generated by anaconda
#
# Note that you do not have to rerun grub after making changes to this
file
# NOTICE:  You do not have a /boot partition.  This means that
#          all kernel and initrd paths are relative to /, eg.
#          root (hd0,0)
#          kernel /boot/vmlinuz-version ro root=/dev/md0
#          initrd /boot/initrd-version.img
#boot=/dev/sda
default=0
timeout=10
splashimage=(hd0,0)/boot/grub/splash.xpm.gz
title Red Hat Linux (2.4.20-18.9)
        root (hd0,0)
        kernel /boot/vmlinuz-2.4.20-18.9 ro root=/dev/md0
        initrd /boot/initrd-2.4.20-18.9.img
title Red Hat Linux (2.4.20-6)
        root (hd0,0)
        kernel /boot/vmlinuz-2.4.20-6 ro root=/dev/md0
        initrd /boot/initrd-2.4.20-6.img




-- 
redhat-list mailing list
unsubscribe mailto:[EMAIL PROTECTED]
https://www.redhat.com/mailman/listinfo/redhat-list

Reply via email to