DOH! Jack, you are absolutely correct. When I pulled a cavity off the panel, it became obvious real fast. Sorry for adding to the confusion.
Steve WA6ZFT On Thursday 17 February 2005 21:20, Jack Davis wrote: > The lock nuts go on the mounting part of the cavities and not on the > threaded rods. The ends of the mounts are slotted as I recall and tapered, > when you tighten the lock nuts on them it pinches the tuning rod and locks > it in place. The lock nuts should be the same size as the nuts that mount > the cavities to the 19 inch rack panel. As insurance most of the knobs were > removed to keep unwanted hands from helping you out at co-located sites. > > Jack > K6YC > ----- Original Message ----- > From: "Steve Rodgers" <[EMAIL PROTECTED]> > To: <[email protected]> > Sent: Thursday, February 17, 2005 7:21 PM > Subject: Re: [Repeater-Builder] Source for Moto T1504 duplexer locking > nuts? > > > Hi, > > > > I received these today, and they are way too big! They just slide right > > over > > the threads. The diameter of the threaded rod is smaller than 1/2". I > > measured with my dial calipers and the diameter is more like 0.370". > > > > > > Steve > > WA6ZFT > > > > On Wednesday 16 February 2005 07:50, Jack Davis wrote: > >> 94830A550 > >> Cadmium-Plated Stl Hex Thin Flex-Top Locknut 1/2"-20 > >> Screw Size, 3/4" Width, 21/64" Height > >> In stock at $10.91 per Pack > >> This item is only sold in Packs of 10 > >> > >> Packs of 10 > >> > >> > >> > >> http://www.mcmaster.com/ > >> > >> > >> Here you go! > >> > >> Jack > >> K6YC > >> > >> ----- Original Message ----- > >> From: "mch" <[EMAIL PROTECTED]> > >> To: <[email protected]> > >> Sent: Wednesday, February 16, 2005 1:17 AM > >> Subject: Re: [Repeater-Builder] Source for Moto T1504 duplexer locking > >> nuts? > >> > >> > Well, this will give you the specs on it. It subs to another number, > >> > and > >> > that other part is NLA, but the description is still there. > >> > _______________________________________________ > >> > Item number. 0210397A06 * The item 0210397A06 has been replaced > >> > with 0210348A05. Selecting this > >> > item will add 0210348A05 to your cart. > >> > 0210348A05: Item has been cancelled > >> > > >> > NUTLCK 1/2-20X5/16 HEX STL CAD > >> > Unit of Measure: 3 PK > >> > _______________________________________________ > >> > > >> > Joe M. > >> > > >> > Mike Morris WA6ILQ wrote: > >> >> At 12:59 PM 2/15/05, you wrote: > >> >> >I have a Motorola T1504 duplexer in need of 4 locking nuts. The > >> >> >locking > >> >> >nut part number is 2-10397A06, but a call to Motorola parts > >> >> > indicates the > >> >> >part number isn't on file. Does anyone have any recommendations for > >> >> > a substitute part, and do they know what the nut size and thread > >> >> > pitch are for the locking nut? > >> >> > > >> >> >Steve > >> >> >WA6ZFT > >> >> > >> >> As I understand from a friend they've been NLA for a few years. > >> >> > >> >> I need 6 or so and am almost ready to call in a > >> >> favor and have a friend make some on a lathe, > >> >> starting with hex stock. > >> >> > >> >> Mike > >> >> > >> >> > >> >> Yahoo! Groups Links > >> > > >> > Yahoo! Groups Links > >> > >> Yahoo! Groups Links > > > > Yahoo! Groups Links > > Yahoo! Groups Links > > > Yahoo! Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/Repeater-Builder/ <*> To unsubscribe from this group, send an email to: [EMAIL PROTECTED] <*> Your use of Yahoo! Groups is subject to: http://docs.yahoo.com/info/terms/
